IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM
- Authors
-
-
S.A. ALABI
Federal University of Technology, Akure, Nigeria
-
- Keywords:
- ballasted track, field test, Bayesian model updating, MCMC, low-amplitude vibration
- Abstract
-
The current design approach of railway sleeper is majorly based on some simplifications considered in the European guidelines. One example of these simplifications is how the distribution of the ballast under the sleeper is accounted for. When ballast is damaged, the stiffness it provided to support the sleeper is reduced and the dynamic behavior of the sleeper changes. However, these guidelines consider a uniform distribution of ballast stiffness, either along the complete length of the sleeper or limited to the rail seat. The embedding ballast conditions of railway tracks seemingly vary randomly from site to site and the ballast-sleeper interaction is neither uniformly distributed nor fixed. Therefore, there is need to evaluate the health status of the ballast under the existing railway track. A field test was carried out on an existing ballasted track, to obtain the time domain responses under impact excitation. The measured vertical vibrations at different locations on the in-situ sleeper were employed in time-domain Markov chain Monte Carlo (MCMC)-based Bayesian model updating for identification of the railway track system. MCMC was used to ensure that proposed method can be applied even when the problem is unidentifiable. The proposed method identified the distribution of railway ballast stiffness under low-amplitude vibration and the “equivalent†rail stiffness and mass. The model updating results confirmed that the ballast stiffness under the existing sleeper was uniform, which implies that there was no ballast damage under the tested sleeper.
- References
- Downloads
- Published
- 2020-11-24
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- P. B. Mogaji, O. A. Raimi, Determination of Optimum Parameters for Drilling Stainless Steel using Response Surface Methodology (RSM) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- P. M. Enyong, Performance of a Short Transmission Line Module under Various Loads: A Comparative Evaluation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Y. O. Olasoji, Characterization of Noise in Narrowband Power Line Communications , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- T. B. Afeni, Slope Monitoring using Total Station – a look at the effect of glass shapes on distance measurements with total station , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- J. A.V. Famurewa, E. T. Faboya, The Effects of Drying Temperature on the Physicochemical Properties of Ogbono (lrvingia Gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. O. Daramola, I. O. Oladele, O. S. AKINTAYO, MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, M. S. Obot, A. S. Ogunlowo, Modelling the Dehydration Characteristics of Taro (Colocasia Esculenta) Slices in a Convective Cabinet Dryer , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- I. M. Sanni, H. A. Ahmed, U. A. Abubakar, S. A. Abdullahi, Spatio-Temporal Analysis of Temperature Trend Of Hadeija-Jama’are River of the Chad Basin in Northern Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
You may also start an advanced similarity search for this article.