DESIGN OF A DUAL DELTA FUSED DEPOSITION MODELLING 3D PRINTER FOR STUDIO CERAMICS PRODUCTION IN NIGERIA

Authors

  • Adekoya A. A

    Federal University of Technology, Akure

  • Adelabu, O. S.

    Federal University of Technology, Akure, Nigeria

  • Kolawole, F. O.

    Institute, Ilesha, Osun State, Nigeria

DOI:
https://doi.org/10.51459/futajeet.2025.19.1.480
Keywords:
Fused deposition modelling, low-cost 3D printer, polylactic acid filament, finite element analysis, ceramic 3D printing
Abstract

A Fused Deposition Modelling (FDM) Delta-type 3D printer was designed and fabricated using locally sourced materials for several components. The design was based on the open-source Replicating Rapid Prototyper (RepRap) platform. The printer features a build volume of 288 mm × 288 mm × 910 mm and utilises a control system comprising a RE-ARM board and a RAMPS 1.6 interface, operating with Marlin firmware. The structure incorporates plain hollow rods, plywood frames, 3D-printed parts, and various electronic components. Finite Element Method (FEM) analysis was conducted on critical 3D-printed parts to assess their structural integrity under operational conditions. The results showed that the von Mises stress values were well below the material's yield strength, while the displacements remained within acceptable limits for high-precision applications. These findings confirm that the components are capable of maintaining both structural integrity and dimensional accuracy during use. Moreover, the total power requirement of the 3D printer was estimated to be 130.32 W, which fits within a moderate energy consumption range when compared with typical desktop FDM 3D printers. The fabricated printer was tested in producing models for clay-cast moulds, though further improvements are recommended.

Author Biographies
  1. Adekoya A. A, Federal University of Technology, Akure

    Department of Industrial Design, 

  2. Adelabu, O. S. , Federal University of Technology, Akure, Nigeria

    Department of Industrial Design

  3. Kolawole, F. O., Institute, Ilesha, Osun State, Nigeria

    Prototype Engineering Development 

References

Adelabu, O. S., and Kashim, I. B. (2011). Developing computer-aided tools for ceramic prototyping in Nigeria. In J. A. B. Olujimi, M. O. Bello, E. B. Ojo, A. O. Olotuah, M. A. Adebayo, and F. K. Omole (Eds.), Proceedings of the International Conference of the School of Environmental Technology, Federal University of Technology, Akure (p. 458–464). School of Environmental Technology, Federal University of Technology, Akure.

Chen, Z., Li, Z., Li, J., Liu, C., Lao, C., Fu, Y., Liu, C., Li, Y., Wang, P., and He, Y. (2019). 3D printing of ceramics: A review. Journal of the European Ceramic Society, 39(4), 661–687.

Dhinakaran, V., Kumar, K. P. M., Ram, P. M. B., Ravichandran, M., Vinayagamoorthy, M., Manoj Kumar, K. P., Bupathi Ram, P. M., Ravichandran, M. and Vinayagamoorthy, M. (2020). A review on recent advancements in fused deposition modeling. Materials Today: Proceedings, 27(xxxx), 752–756.

Farayibi, P. K. and Abioye, T. E. (2017a). A study on the awareness level of additive manufacturing technology in south-western Nigeria. African Journal of Science, Technology, Innovation and Development, 9(2), 157–162.

Farayibi, P. K. and Abioye, T. E. (2017b). A study on the awareness level of additive manufacturing technology in south-western Nigeria. African Journal of Science, Technology, Innovation and Development, 9(2), 157–162.

Farayibi, P. K., Dioha, J. O., Orukotan, J. and Omiyale, B. O. (2019a). Development of a Fused Deposition Modelling Machine for Plastic-Based Additive Manufacturing Purposes. Assumption University E- Journal of Interdisciplinary Research, 4(2), 1–11.

Farayibi, P. K., Dioha, J. O., Orukotan, J. and Omiyale, B. O. (2019b). Development of a Fused Deposition Modelling Machine for Plastic-Based Additive Manufacturing Purposes. Assumption University E-Journal of Interdisciplinary Research, 4(2), 1–11.

Inoma, A. O., Ibhadode, O. O. and Ibhadode, A. A. O. (2020). The perception and deployment of 3D printing in the Nigerian educational sector for science and engineering programs. Scientific African, 10, 1-10.

Klenam, D. E. P., Bamisaye, O. S., Williams, I. E., Van Der Merwe, J. W. and Bodunrin, M. O. (2022). Global perspective and African outlook on additive manufacturing research - an overview. Manufacturing Review, 9, 128–131.

Oluwajobi, A. O. and Kolawole, F. O. (2021). Design of a Fused Filament Fabrication (FFF) 3D printer. Nigerian Journal of Technology, 40(2), 252–260.

Oluwajobi, A. O. and Kolawole, F. O. (2022). Development and evaluation of a Fused Filament Fabrication (FFF) 3-D printer. Nigerian Journal of Technology, 40(5), 829–836.

Oluwajobi, A. O. and Osunkoya, R. O. (2020). Development of a Low-Cost Fused Filament Fabrication (FFF) 3D-Desktop Printer. Nigerian Journal of Materials Science and Engineering, 10, 81–90.

Siciliano, B. and Khatib, O. (Eds.). (2008). Springer handbook of robotics. Springer. Simons, A., Avegnon, K. L. M. and Addy, C. (2019). Design and Development of a Delta 3D Printer Using Salvaged E-Waste Materials. 2019.

Song, X. (2016). Slurry based stereolithography: A solid freeform fabrication method of ceramics and composites. Doctoral dissertation, University of Southern California. ProQuest Dissertations Publishing.

Steuben, J., Van Bossuyt, D. L. and Turner, C. (2015). Design for fused filament fabrication additive manufacturing. In Proceedings of the ASME 2015 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC/CIE2015) (8). American Society of Mechanical Engineers.

Zhou, L., Miller, J., Vezza, J., Mayster, M., Raffay, M., Justice, Q., Al Tamimi, Z., Hansotte, G., Sunkara, L. D. and Bernat, J. (2024). Additive manufacturing: A comprehensive review. Sensors, 24(9), 1-44.

Cover Image
Downloads
Published
2025-05-30
Issue
Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
Section
Articles
License

Copyright (c) 2025 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Copyright

With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.

How to Cite

DESIGN OF A DUAL DELTA FUSED DEPOSITION MODELLING 3D PRINTER FOR STUDIO CERAMICS PRODUCTION IN NIGERIA. (2025). FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY, 19(1), 197-207. https://doi.org/10.51459/futajeet.2025.19.1.480

Similar Articles

101-110 of 131

You may also start an advanced similarity search for this article.