BRIDGING RESEARCH-INDUSTRY DIVIDE IN FOOD AND BEVERAGE ENTERPRISES: EMPIRICAL EVIDENCE FROM SOUTHWESTERN NIGERIA
- Authors
-
-
A D Dada
-
- Keywords:
- Research and Development (R&D), SMEs, Competitiveness, Support services, Nigeria, Technological Innovations, Food and Beverage companies
- Abstract
-
This paper investigates the gaps between research institutions and industry in R&D collaboration towards the promotion of innovation, creativity and competitiveness among food and beverage enterprises (FBEs) in Nigeria. This was measured by the level impact of R&D institutional support services for technological innovations in the industry. A multi-staged sampling method was adopted to select 150 registered FBEs from three small and medium scale enterprises (SMEs) populated States in Southwestern Nigeria with a response rate of 64% recorded. Adopting model regression analysis, the study showed that the contributions of R&D institutions to innovative performance of the industry was low (R2 = 0.008). However, training and information dissemination (β=36.49, P≤ 0.05) and provision of analytical services (β = 36.67, P≤ 0.05) were found to have significant impact on the innovative performance of the industry. No significant difference (F=0.336, P≤ 0.05) between the two methods of support services was confirmed in the study. The study concludes that the R&D support services from research institutions to FBEs were inadequate. Policy intervention is needed to encourage R&D institutions to adequately support the food and beverage industry in Nigeria.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O. O. Awopetu, P. K. Farayibi, K. A. Ismail, Optimization of Major Process Parameters for Surface Roughness of ASTM 25 Grey Cast Iron using Taguchi method , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- E.O. OLUKANNI, O.J. OYEDEPO, PHYSICO-RHEOLOGICAL CHARACTERIZATION OF POLYMER MODIFIED BITUMEN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. C. Chukwuma, Promax2100: A Computer Programme for Design and Optimization of Mineral Processing Plant , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- N S Lawal, A A Babalola, O O Adama, A O Sosanya, A A Adebayo, CHARACTERIZATION OF DIFFERENT CASSAVA EFFLUENTS AND EVALUATION OF PROCESSOR ON-SITE HANDLING TECHNIQUES IN OGUN STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, D. A. Agboola, Labour Productivity Assessment of Dredging Operations in Some Selected Companies in Lagos State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Taiwo, I. O. Oladele, O. O. Daramola, A. D. Akinwekomi, O. G. Agbabiaka, Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.