FLEXURAL MOTION UNDER MOVING MASSES OF PRESTRESSED SIMPLY SUPPORTED PLATE RESTING ON BI-PARAMETRIC FOUNDATION
- Authors
-
-
T O Awodola
Department of Mathematics, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Prestress, Rotatory Inertia, Bi-parametric Foundation, Resonance, Critical speed, Mass Ratio.
- Abstract
-
In this investigation, the flexural vibration of a prestressed and simply supported rectangular plate carrying moving concentrated masses and resting on bi-parametric (Pasternak) elastic foundation is considered. In order to solve the governing fourth order partial differential equation, a technique based on separation of variables is used to reduce the equation with variable and singular coefficients to a sequence of coupled second order ordinary differential equations. The modified method of Struble and the integral transformations are then employed for the solutions of the reduced equations. The numerical results in plotted curves show that as the value of the axial force in x-direction (Nx) increases, the response amplitudes of the plates decrease, the same effect is produced as the axial force in y-direction (Ny) increases for both cases of moving force and moving mass problems of the prestressed and simply supported rectangular plate resting on Pasternak elastic foundation. The deflection of the plate also decreases in each case as the values of the Shear modulus Go and the rotatory inertia correction factor Ro increase. Also, the transverse deflections of the prestressed rectangular plates under the actions of moving masses are higher than those obtained when only the force effects of the moving loads are considered. Further analysis shows that resonance is attained earlier in moving mass problem than in moving force problem and that the critical speed for the moving mass problem is reached prior to that of the moving force problem, implying that it is risky to rely on a design based on the moving force solution. Furthermore, the response amplitudes of the moving mass problem increase with increasing mass ratio and approach those of the moving force as the mass ratio approaches zero for the prestressed and simply supported rectangular plates resting on uniform Pasternak elastic foundation
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- T E Abioye, DEVELOPMENT OF A POULTRY DE-FEATHERING MACHINE WITH AN ADJUSTABLE BASIN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, Analyses of Biogas and Digestate from Cattle Dung Anaerobic Digestion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Bamiji Zacheous Adewole, EXPERIMENTAL STUDY ON BED-TO-TUBE HEAT TRANSFER COEFFICIENTS IN BUBBLING FLUIDIZED BED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. G. Agbabiaka, A. S. Ogunbadejo, M. A. Okoro, Assessment of Mechanical Properties of Hybrid Composites Based on Polypropylene and Vegetable Fibers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. E. Abiodun, Determining The Metal Contents of Leach Liqour from Ihietutu Lead and Zinc Ore, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- S.A. ALABI, IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Samuel Olugbenga Oladele, MODELLING OF THIN-LAYER MICROWAVE DRYING OF BITTER LEAF SAMPLES (Vernonia Amygdalina) FOR PRESERVATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Robert Oluwayimika Abolade, Oluwaseun Olayinka Tooki, David Oluwagbemiga Aborisade, REVIEW ARTICLE ON THE MITIGATION OF FOUR WAVE MIXING IN OPTICAL COMMUNICATION SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.