EXPERIMENTAL STUDY ON BED-TO-TUBE HEAT TRANSFER COEFFICIENTS IN BUBBLING FLUIDIZED BED
- Authors
-
-
Bamiji Zacheous Adewole
Obafemi Awolowo University, Ile-Ife, Osun State
-
- Keywords:
- Fluidized bed, Co-firing, Coal, Coconut shell, Bed-to-tube, Heat transfer
- Abstract
-
The overall bed-to-tube heat transfer coefficients of the blends of Lafia-obi coal and coconut shells have been investigated in a bubbling fluidized bed combustor. Experiments were performed at five different particle sizes of coal (5, 10, 15, 20 and 25 mm) and five different particle sizes of coconut shells (2, 6, 10,14 and 18 mm) for different blend proportions of 10%, 20%, 30%, 40% and 50%. Results obtained showed that the overall bed-to-tube heat transfer coefficient decreased with increasing coconut shell particle size in the blends. Combined effects of high radiation from large particle size of coal (25 mm) and high convection heat from small particle size of coconut shell (2 mm) at blend proportion of 10 and 50% produced the maximum bed-to-tube heat transfer coefficient. Due to the importance of heat exchange in the fluidized bed, it is observed that the contribution of biomass co-firing with coal is significant, hence, co-firing at optimal particle size and biomass blend ratio is imperative for achieving higher bed-to-tube heat transfer in the fluidized bed boiler.
- References
- Downloads
- Published
- 2021-11-29
- Section
- Articles
- License
-
Copyright (c) 2021 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Oluseyi Orisadare, Ayodeji S. Olawore, Michael O. Ibiwoye, Eyitayo A. Ponle, Omolola T. Odeyemi, Opeyemi S. Kegbeyale, MECHANICAL AND MICROSTRUCTURAL PROPERTIES OF BRASS REINFORCED WITH COCONUT SHELL ASH POWDER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- K. O. Oladosu, E. O. Olafimihan, K. A. Babatunde, B. Kareem, A. A. Mustapha, Investigation of Staged Air supply on Grate Combustion of Palm Kernel Shell Mixed with Selected additives (Al2O3 and CaO) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Anthony T. Bolarinwa, Gideon C. Nwafor, OPEN PIT OPTIMIZATION AND PRODUCTION SCHEDULING OF OKOBO COAL MINE, CENTRAL NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. G. Agbabiaka, A. S. Ogunbadejo, M. A. Okoro, Assessment of Mechanical Properties of Hybrid Composites Based on Polypropylene and Vegetable Fibers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- E. O. Olutomilola, T. I. Ogedengbe, Evaluation of the Effect of Constituents on Insulation Quality of Selected Biomass Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- A. S. Taiwo, I. O. Oladele, O. O. Daramola, A. D. Akinwekomi, O. G. Agbabiaka, Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
