LYSIMETER DETERMINATION OF CROP COEFFICIENT OF DRIP IRRIGATED JATROPHA CURCAS
- Authors
-
-
T A EWEMOJE
Agricultural and Environmental Engineering Department, University of Ibadan, Nigeria
-
S D FAGBAYIDE
Agricultural and Bio-Environmental Engineering Department, Federal Polytechnic Ilaro, Ogun State, Nigeria
-
K O OLUWASEMIRE
Agronomy Department, University of Ibadan, Nigeria
-
- Keywords:
- Mini-drainage lysimeter, soil water balance, Jatropha crop coefficient and drip irrigation
- Abstract
-
The study was designed to examine the actual evapotranspiration and crop coefficient (Kc) of eight months old Jatropha curcas grown in mini-drainage lysimeter with a cylindrical drum of circular cross-sectional area of 0.246 m2, diameter 0.56 m and 1.0 m depth. Investigation was conducted with drip irrigation system using five mini lysimeters. Each lysimeter contained one pressure compensating emitter of 4L/hr. Climatic variables were obtained for the determination of reference evapotranspiration (ETo) using the FAO-Penman Monteith model. The value for the crop evapotranspiration (ETc) was determined from the lysimeter using the soil water balance method on daily basis and the crop factor (Kc) was estimated from the ratio of ETc / ETo. The ETo estimated from weather data for the crop growing season ranged from 19.3 to 33.1 mm/day. The average crop coefficient (Kc) values at different growth stages were 0.6, 0.9, 1.2 and 0.8 for the initial, development, mid-season and late season respectively. The research output will enhance the productivity of farmers with optimum water management on large scale Jatropha cultivation.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- K. F. Akingbade, Development of Chemical Proportion Formulation Model for Quality Control in Flexible Polyurethane Foam Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- O. ADERINLEWO, B. ARIBISALA, A. AFOLAYAN, M. TANIMOLA, COMPARATIVE ANALYSIS OF THE USE OF BAMBOO STEM ASH AND CEMENT FOR LATERITIC SOIL STABILIZATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- E. O. Ajaka, O. E. Abiodun, Determining The Metal Contents of Leach Liqour from Ihietutu Lead and Zinc Ore, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- A. S. Adewuyi, J. R. Adewumi, Optimization of Coagulation-Flocculation Process for the Treatment of Wastewater Using Inorganic and Three Natural Coagulants , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- E. C. Umeh, A. F. Isiaka, Analysis of the Short Fall in Production Target and Specific Cost of Unit Operations in National Iron Ore Mining Company NIOMCO, Itakpe. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Obinna Obiora-Okeke, J. R. Adewumi, O. M. Ojo, IMPACT OF LAND USE AND LAND COVER CHANGES ON RUNOFF PREDICTION IN OGBESE RIVER WATERSHED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.