LYSIMETER DETERMINATION OF CROP COEFFICIENT OF DRIP IRRIGATED JATROPHA CURCAS
- Authors
-
-
T A EWEMOJE
Agricultural and Environmental Engineering Department, University of Ibadan, Nigeria
-
S D FAGBAYIDE
Agricultural and Bio-Environmental Engineering Department, Federal Polytechnic Ilaro, Ogun State, Nigeria
-
K O OLUWASEMIRE
Agronomy Department, University of Ibadan, Nigeria
-
- Keywords:
- Mini-drainage lysimeter, soil water balance, Jatropha crop coefficient and drip irrigation
- Abstract
-
The study was designed to examine the actual evapotranspiration and crop coefficient (Kc) of eight months old Jatropha curcas grown in mini-drainage lysimeter with a cylindrical drum of circular cross-sectional area of 0.246 m2, diameter 0.56 m and 1.0 m depth. Investigation was conducted with drip irrigation system using five mini lysimeters. Each lysimeter contained one pressure compensating emitter of 4L/hr. Climatic variables were obtained for the determination of reference evapotranspiration (ETo) using the FAO-Penman Monteith model. The value for the crop evapotranspiration (ETc) was determined from the lysimeter using the soil water balance method on daily basis and the crop factor (Kc) was estimated from the ratio of ETc / ETo. The ETo estimated from weather data for the crop growing season ranged from 19.3 to 33.1 mm/day. The average crop coefficient (Kc) values at different growth stages were 0.6, 0.9, 1.2 and 0.8 for the initial, development, mid-season and late season respectively. The research output will enhance the productivity of farmers with optimum water management on large scale Jatropha cultivation.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O. O. Awopetu, P. K. Farayibi, K. A. Ismail, Optimization of Major Process Parameters for Surface Roughness of ASTM 25 Grey Cast Iron using Taguchi method , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- J. A.V. Famurewa, E. T. Faboya, The Effects of Drying Temperature on the Physicochemical Properties of Ogbono (lrvingia Gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Tasiu Ashiru Sulaiman, Ibrahim Aliyu, Yusuf Yau, Ibrahim Bello, ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- T. I. Mohammed, ACHIEVING THE SELECTION OF OPTIMAL PRESS BRAKE DESIGN VIA A FUZZY TOPSIS APPROACH , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, O. S. Adekinya, Assessment of Cost Effectiveness of Borehole Drilling in Oyo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Samuel L Akingbonmire, L Samuel, O Oluwafemi Omotayo, J O Afolayan, A Banjo Olorunshola, THE PHYSICO-CHEMICAL PROPERTIES OF SOME FINE AGGREGATES IN LOKOJA, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.