EVALUATION OF EFFECTS OF SELECTED FACTORS ON ADSORPTION KINETICS OF LEAD ION REMOVAL FROM AQUEOUS SOLUTIONS
- Authors
-
-
A Amoko
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria
-
S JUSTINAH
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria;
-
A Fehintola
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria;
-
O Ezekiel
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
I Oke
at Civil and Environmental Engineering Department, Elizade University, Ilara- Mokin, Ondo State, Nigeria.
-
A Isaiah
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
- Keywords:
- Lead, Adsorption Kinetics, Microsoft Excel Solver, Analysis of Variance, Mass of Adsorbents, Significant Factors
- Abstract
-
This paper presents a report on the removal of lead ions (Pb2+) from aqueous solutions through adsorption techniques using powdered corncobs. Corncobs were collected from Obafemi Awolowo University agricultural farm. The corncobs were washed with distilled water to remove impurities. The corncobs were dried at room temperature, pulverized, sieved into different particle sizes using standard sieve sizes and stored. Powdered corncobs (PCCS) were separated based on the size. Its micrograph structure, physical and chemical properties were determined using standard methods. The PCCS was used as an adsorbent to remove Pb2+ from aqueous solutions and raw water through batch processes. Effects of the mass of the adsorbent, the initial concentration of Pb2+, initial pH of the aqueous solution and particle size of PCCS on the adsorption kinetics and its models’ parameters were evaluated.
The study shown that moisture content of the PCCS was 7.29 %, volatile solid at 550oC and 1200oC were 96.88 % and 99.44 % respectively. It was also revealed that mass of adsorbent, pH, particle size of the adsorbent, initial concentration of Pb2+ and adsorption time were significant factors that had effects on adsorption of Pb2+ onto PCCS at 95 % confidence level. It was concluded that lead ion can be removed by PCCS, the mass of the adsorbent had significant effects on adsorption kinetics.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- E O Olutomilola, A Omoaka, THEORETICAL DESIGN OF A PLANTAIN PEELING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, POLLUTION OF VEHICULAR EMISSION ANALYSIS AT FEDERAL UNIVERSITY OF TECHNOLOGY AKURE NORTH GATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- S. A. Alabi, I. A. Arighaye, J. O. Afolayan, PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Samuel Olugbenga Oladele, MODELLING OF THIN-LAYER MICROWAVE DRYING OF BITTER LEAF SAMPLES (Vernonia Amygdalina) FOR PRESERVATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Ashiru Mohammed, Ibrahim Aliyu, Hussaini Abdullahi Umar, Aliyu Umar Mani, PERFORMANCE EVALUATION OF RAILWAY BALLAST DEGRADATION USING THE MORPHOLOGICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- D. J. Afu, E. O. Ifelola, S. G. Ayodele, A. Ekun, A. Itunu, Survey of the Effects of Operational Noise on Quarry Workers in Akoko-Edo Local Government Area of Edo State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- W. O. Apena, G. A. Oladunni, Comparative Analysis of Path Loss Prediction Models for Selected Rural Areas in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.