Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables
- Authors
-
-
T. S. Mogaji
Department of Mechanical Engineering, Federal University of Technology, Akure
-
- Keywords:
- Array, Array, Array, Array, Array, Array
- Abstract
-
An improved vapour compression refrigeration system (VCRS) was developed for the preservation of fresh vegetables and its performance was evaluated. The cooling system operating with R134a as working fluid consists of an evaporator, compressor, condenser, capillary tube and a redesigned temperature control device (TCD). The refrigeration system has capacity to accommodate 0.02 metric tonnes (20 kg) of any fresh vegetables. The improved cooling system was used to preserve fresh vegetables such as: bitter leaf (Vernonia amygdalina Delile) and pumpkin leaf (Telfairia occidentalis). Study was conducted to check the freshness of the vegetables and data were observed daily. Results of the transient performance tests revealed that an average cabinet and ambient temperature of 3.64C and 26.89C were observed, and an average cabinet and ambient relative humidity of 94.50% and 45.23% were recorded respectively for the preserved vegetables. The needed optimum storage temperature range for the preservation of the selected vegetables samples were attained in cooling system at 2C – 4C with the aids of the incorporated newly designed TDC. The improved domestic vapour compression refrigeration system performed up to expectation as the shelf life of the tested sample inside the cooling system was extended by fourteen days relative to ambient storage.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Ubochi, B. C, Olawumi, A. E., , Shuiabu, A. O. , Akingbade, K. F, A WEARABLE FACIAL RECOGNITION DEVICE FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Satimehin, A., Fayose, F, Adewale D, Adewoyin. O, EFFECT OF EXTRUSION PROCESS ON PERFORMANCE OF AN INDIGENOUS EXTRUDER AND QUALITY OF CASSAVA PRODUCTS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- Akinola, A. O, Abdulkadir, M, Bello, E. I, Adedeji, S. Y., PRODUCTION AND CHARACTERIZATION OF BIODIESEL FROM MARULA (Sclerocarya birrea) SEED OIL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 2 (2022): FUTA Journal of Engineering and Engineering Technology
- Arum, C, Akande, S. P, Alabi, S. A., STRENGTH EVALUATION OF POZZOLANIC CONCRETE CONTAINING CALCINED CERAMIC WASTE AND GLASS WASTE POWDER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- Samuel Olugbenga Oladele, MODELLING OF THIN-LAYER MICROWAVE DRYING OF BITTER LEAF SAMPLES (Vernonia Amygdalina) FOR PRESERVATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- R. F. Falayi, P. A. Adeduntan, EFFECTS OF WOODASH AND SAWDUST ADMIXTURE ON ENGINEERING PROPERTIES OF BURNT LATERITE CLAY BRICKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Ijagbemi, C.O. , Olabanji, O. M, Abdulmumuni, B, Ashiru, A.R, IJagbemi F.M, PRODUCTION OF ETHANOL GEL FROM CASSAVA AND BANANA PEELS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- AWOPETU, O. O, OWOYEMI, J. M, BABATUNDE, T. P. , OJO, O. T., DEVELOPMENT OF A TRANSFORMABLE FURNITURE SYSTEM: FROM SHELVING UNIT TO FUNCTIONAL TABLETOP , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Mogaji, T.S, Egunbiyi, T.O, DESIGN AND SIMULATION OF TURBOCHARGER-DERIVED MICROTURBINE SYSTEM FOR COMBINED HEAT AND POWER GENERATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.