Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables
- Authors
-
-
T. S. Mogaji
Department of Mechanical Engineering, Federal University of Technology, Akure
-
- Keywords:
- Array, Array, Array, Array, Array, Array
- Abstract
-
An improved vapour compression refrigeration system (VCRS) was developed for the preservation of fresh vegetables and its performance was evaluated. The cooling system operating with R134a as working fluid consists of an evaporator, compressor, condenser, capillary tube and a redesigned temperature control device (TCD). The refrigeration system has capacity to accommodate 0.02 metric tonnes (20 kg) of any fresh vegetables. The improved cooling system was used to preserve fresh vegetables such as: bitter leaf (Vernonia amygdalina Delile) and pumpkin leaf (Telfairia occidentalis). Study was conducted to check the freshness of the vegetables and data were observed daily. Results of the transient performance tests revealed that an average cabinet and ambient temperature of 3.64C and 26.89C were observed, and an average cabinet and ambient relative humidity of 94.50% and 45.23% were recorded respectively for the preserved vegetables. The needed optimum storage temperature range for the preservation of the selected vegetables samples were attained in cooling system at 2C – 4C with the aids of the incorporated newly designed TDC. The improved domestic vapour compression refrigeration system performed up to expectation as the shelf life of the tested sample inside the cooling system was extended by fourteen days relative to ambient storage.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- S. O. Balogun, S. A. Yaro, M. Abdulwahab, A. Kasim, PRODUCTION AND CHARACTERIZATION OF ALUMINA NANOPARTICLES FROM GIRO CLAY VIA ACID LEACHING WITH SOL GEL METHOD , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- P. A. Adesida, W. A. Salawudeen, ASSESSMENT OF THE INFLUENCE OF MECHANICAL PROPERTIES AND MINERALOGICAL COMPOSITION ON FRAGMENTATION OF SELECTED GRANITIC ROCKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- O. A. Agbolade, EVALUATING LORAWAN ADAPTIVE DATA RATE EFFECTIVENESS IN HETEROGENOUS SMART FARMING CONDITIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- I. O. Oladele, O. O. Daramola, A. Oyetunji, Appropriate Technological Procedures for Fusion Welding of Low Alloy Carbon Steel , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Oluwaseun Opeyemi Martinsa, Muhammad Abdulhamid Mahdia, David Tiwaloluwa Adegokea, Olusola Esther Omoniyia, Pius Benmoore Gabriela, DESIGN AND IMPLEMENTATION OF AN ELECTRONIC ATTENDANCE AND ADMITTANCE SYSTEM WITH FINGERPRINT AUTHENTICATION USING PATTERN MATCHING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, M. S. Obot, A. S. Ogunlowo, Modelling the Dehydration Characteristics of Taro (Colocasia Esculenta) Slices in a Convective Cabinet Dryer , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- A. S. Ojo, M. O. Alatise, Spatial Variability of Soil Physical Properties of a Typical Fadama Farmland (Ayede Ogbese) in South Western, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Oji, I. C., Ale, T. O, Odeyemi, C. S, MODELLING AND SIMULATION OF FAULTS AND FAULT LOCATION DETECTOR FOR RADIAL DISTRIBUTION SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Arowolo, M.O., , Adaralode, C.I. , Ogundigba, H.B, DEVELOPMENT AND IMPLEMENTATION OF A COMPUTER VISION-BASED POTHOLE DETECTOR USING INFRARED CAMERA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.