Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables
- Authors
-
-
T. S. Mogaji
Department of Mechanical Engineering, Federal University of Technology, Akure
-
- Keywords:
- Array, Array, Array, Array, Array, Array
- Abstract
-
An improved vapour compression refrigeration system (VCRS) was developed for the preservation of fresh vegetables and its performance was evaluated. The cooling system operating with R134a as working fluid consists of an evaporator, compressor, condenser, capillary tube and a redesigned temperature control device (TCD). The refrigeration system has capacity to accommodate 0.02 metric tonnes (20 kg) of any fresh vegetables. The improved cooling system was used to preserve fresh vegetables such as: bitter leaf (Vernonia amygdalina Delile) and pumpkin leaf (Telfairia occidentalis). Study was conducted to check the freshness of the vegetables and data were observed daily. Results of the transient performance tests revealed that an average cabinet and ambient temperature of 3.64C and 26.89C were observed, and an average cabinet and ambient relative humidity of 94.50% and 45.23% were recorded respectively for the preserved vegetables. The needed optimum storage temperature range for the preservation of the selected vegetables samples were attained in cooling system at 2C – 4C with the aids of the incorporated newly designed TDC. The improved domestic vapour compression refrigeration system performed up to expectation as the shelf life of the tested sample inside the cooling system was extended by fourteen days relative to ambient storage.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Agbolade, O. A, Ogunyemi, B. I., DEVELOPMENT OF A LIBRARY MANAGEMENT SYSTEM ON A RASPBERRY PI BASED WIRELESS LOCAL AREA NETWORK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Ugwu, S. J, Nwude, M. O, Shariff, F. U, ANALYSING THE IMPACT OF URBANISATION ON PHYSICO-CHEMICAL GROUNDWATER PARAMETER OF KADUNA METROPOLIS, USING STATISTICAL APPROACH AND BASIC DRINKING WATER STANDARD , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- M. O. Oyeleye, T. O. Ale, Foundational Steel Reinforcement Earthing Evaluation: Case of Ogomudia Electrical/Electronics Laboratory Building Extension, Federal University Of Technology, Akure , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- C. N. Udekwe, A. A. Ponnle, A. O. Omolade, EXPERIMENTAL STUDY ON THE SYNERGISTIC EFFECTS OF COOLING METHODS AND HEAT SINK DESIGN ON THERMOELECTRIC GENERATOR PERFORMANCE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- A. M. Akintade, O. J. Olukunle, J. Isa, Performance Evaluation of an Electromechanical Groundnut Roasting Machine Akintade A.M, Olukunle O. J. and Isa J. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Ogundele, O. J, Adebisi, O. I, Adejumobi, I. A, Amusa, K. A. , Alabi, A. A, POWER QUALITY ENHANCEMENT IN AN ELECTRICAL DISTRIBUTION NETWORK USING SHUNT PASSIVE FILTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Olutomilola E. O., Otokola T. O. , Ajayi V. A., DEVELOPMENT OF AN ADJUSTABLE HOPPER FOR HAMMER MILL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- F. M. Dahunsi, S. O. Oluponna, Analysis of Energy Usage Pattern of a Nigerian University Digital Resource Center (DRC):: FUTA DRC as a Case Study , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- K. O. Oladosu, E. O. Olafimihan, K. A. Babatunde, B. Kareem, A. A. Mustapha, Investigation of Staged Air supply on Grate Combustion of Palm Kernel Shell Mixed with Selected additives (Al2O3 and CaO) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Ojo Oluwole Timothy , 2Adeniji Toyosi Adelowokan, DEVELOPMENT OF A BIOMETRIC, FACIAL RECOGNITION AND AUTHENTICATION SYSTEM FOR CLASS ATTENDANCE MANAGEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.