Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application
- Authors
-
-
A. S. Taiwo
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. O. Daramola
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array, Array
- Abstract
-
This work investigates the effects of particulate palm kernel shell (PKS) on epoxy matrix for the development of composites that can be used as substitute to the conventional metallic bumpers in automobiles. The PKS was sourced from an oil plantation and washed thoroughly with water before sun dried. The dried PKS was pulverized using a laboratory ball mill and sieved into 45 µm particle sizes. Elemental composition of the PKS was determined using XRF. The PKS particulate was randomly dispersed in the epoxy resin to develop composite samples of varied weight contents. The developed samples were tested to determine their impact toughness, wear resistance, flexural, tensile and water absorption properties. The results showed that higher weight contents within 10 - 20 wt.% PKS reinforcement gave the best performance in most of the mechanical properties examined with the exception of tensile and flexural properties which were enhanced at 8 wt.%. Water absorption was noticed to increase as the PKS content increases from 2 - 20 wt.%.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- I. A. Oke, A. O. Obijole, E. A. Adekunbi, J. O. Babajide, M. D. Idi, T. A. Aladesanmi, THERMAL PROPERTY OF CARBON RESIN ELECTRODES DEVELOPED FOR ELECTROCHEMICAL TREATMENT OF WATER AND WASTEWATERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Oyefeso, B, Yusuff, O. A., Fadele, O. K, DEVELOPMENT OF PREDICTIVE MASS AND VOLUME MODELS FOR AFRICAN BUSH MANGO (Irvingia gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- T A EWEMOJE, S D FAGBAYIDE, K O OLUWASEMIRE, LYSIMETER DETERMINATION OF CROP COEFFICIENT OF DRIP IRRIGATED JATROPHA CURCAS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Faluyi, S. O.,, Amu, O. O., Adetoro, E. A., GEOTECHNICAL PROPERTIES OF LIME AND BAMBOO STEM ASH STABILIZED SOILS FOR ROAD CONSTRUCTION IN SOUTH-WESTERN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- Ugwu, S. J, Nwude, M. O, Shariff, F. U, ANALYSING THE IMPACT OF URBANISATION ON PHYSICO-CHEMICAL GROUNDWATER PARAMETER OF KADUNA METROPOLIS, USING STATISTICAL APPROACH AND BASIC DRINKING WATER STANDARD , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Effect of Rake Face Reinforcement on Cutting Tool Life of Cemented Carbide Tools during Turning of a-Titanium Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Oyeleye M. O. , Aminu A. k, EVALUATION OF LIGHTNING PROTECTION OF A SOUTH WEST NIGERIA UNIVERSITY LIBRARY EDIFICE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- O OLANIRAN, J O BORODE, A E AFOLABI, P A OLUBAMBI, B A OLANIRAN, D O FOLORUNSO, CORROSION ASSESSMENT OF SINTER DUPLEX STAINLESS STEEL COMPOSITES IN PINEAPPLE JUICE EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Sunny, O. U.,, Obinnaya, N.,, Japheth, G. C., Nnaemeka, J. A., Bello, Y., ANALYSIS OF AN SC-17M DESIGNED MAIN LANDING GEAR LOADING ACTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- P. M. Enyong, Performance of a Short Transmission Line Module under Various Loads: A Comparative Evaluation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.