Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application
- Authors
-
-
A. S. Taiwo
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. O. Daramola
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array, Array
- Abstract
-
This work investigates the effects of particulate palm kernel shell (PKS) on epoxy matrix for the development of composites that can be used as substitute to the conventional metallic bumpers in automobiles. The PKS was sourced from an oil plantation and washed thoroughly with water before sun dried. The dried PKS was pulverized using a laboratory ball mill and sieved into 45 µm particle sizes. Elemental composition of the PKS was determined using XRF. The PKS particulate was randomly dispersed in the epoxy resin to develop composite samples of varied weight contents. The developed samples were tested to determine their impact toughness, wear resistance, flexural, tensile and water absorption properties. The results showed that higher weight contents within 10 - 20 wt.% PKS reinforcement gave the best performance in most of the mechanical properties examined with the exception of tensile and flexural properties which were enhanced at 8 wt.%. Water absorption was noticed to increase as the PKS content increases from 2 - 20 wt.%.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- K.O. OLADOSU, E.O. OLAFIMIHAN, O.R. OYETUNJI, M.O. ADEOTI, A.A. ADEJARE, Influence of Kaolin Additive on Ash Yield of Palm Kernel-Cashew Shell Combustion: Effect of Kaolin Additive on Ash Yield of Palm Kernel- Cashew Shell Combustion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- George, U. D, Akpan, M. G, Onwe, D. N, MACHINE LEARNING CLASSIFIER FOR DALIUM GUINEENSE FRUIT USING ITS PHYSICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- M O Idris, EVALUATION OF EFFECTS OF EXTERNAL FACTORS ON DUE DATES PREDICTION IN MANUFACTURING JOBSHOPS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- O. M. Adebajo, , Prof. Oluyemi-Ayibiowu, B. D. , K. E. Falola, , ASSESSMENT OF SELECTED MACHINE LEARNING SYSTEMS IN PREDICTING THE RESILIENT MODULUS OF COHESIVE SOILS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Ajaka E. Oyedele, Alabi O. Oladunni , Omotehinse O. Adeyinka , Minimizing Losses, Socio-environmental Problems and Operational Difficulties in the Activities of Artisanal and Small-scale Gold Mining in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- A. O. Omotehinse, MINING SECTOR’S PARTICIPATION IN ADVANCING THE SUSTAINABLE DEVELOPMENT GOALS (SDGs) IN NIGERIA: EXPERIENCES FROM A LARGE-SCALE GOLD MINING COMPANY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- J.A. Ojumu,, EFFECT OF SYNTHESIZED SILVER NANOPARTICLES FROM ALOE VERA PLANT LEAF EXTRACT ON CORROSION BEHAVIOUR OF API 5L IN 0.5M OF H2SO4 , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- A. E. Owoputi, Issues in Safety and Security in Maritime Transportation, Port and Marine Environment , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Olutomilola E. O., Otokola T. O. , Ajayi V. A., DEVELOPMENT OF AN ADJUSTABLE HOPPER FOR HAMMER MILL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.