Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application
- Authors
-
-
A. S. Taiwo
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. O. Daramola
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array, Array
- Abstract
-
This work investigates the effects of particulate palm kernel shell (PKS) on epoxy matrix for the development of composites that can be used as substitute to the conventional metallic bumpers in automobiles. The PKS was sourced from an oil plantation and washed thoroughly with water before sun dried. The dried PKS was pulverized using a laboratory ball mill and sieved into 45 µm particle sizes. Elemental composition of the PKS was determined using XRF. The PKS particulate was randomly dispersed in the epoxy resin to develop composite samples of varied weight contents. The developed samples were tested to determine their impact toughness, wear resistance, flexural, tensile and water absorption properties. The results showed that higher weight contents within 10 - 20 wt.% PKS reinforcement gave the best performance in most of the mechanical properties examined with the exception of tensile and flexural properties which were enhanced at 8 wt.%. Water absorption was noticed to increase as the PKS content increases from 2 - 20 wt.%.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- R. F. Falayi, P. A. Adeduntan, EFFECTS OF WOODASH AND SAWDUST ADMIXTURE ON ENGINEERING PROPERTIES OF BURNT LATERITE CLAY BRICKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- C. C. Chiabuotu, T. E. Abioye, O. M. Olabanji, ENHANCING DEPOSITION QUALITY OF ALUMINUM ALLOY 5356 THROUGH OPTIMIZATION OF WAAM PROCESS PARAMETERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- T E Abioye, DEVELOPMENT OF A POULTRY DE-FEATHERING MACHINE WITH AN ADJUSTABLE BASIN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Adebayo Felix Owa, Abdulahi Olawale Adebayo, Olawale Olarewaju Ajibola, Oluwole Daniel Adigun, Sunday Gbenga Aborisade, Fisayo Adesina, Corrosion Behaviour of Low Carbon Steel in Sulphide Medium Using Thevetia Peruviana as Inhibitor , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, Analyses of Biogas and Digestate from Cattle Dung Anaerobic Digestion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- B. V. Omidiji, H. A. Owolabi, A. A. Oyenuga, A. A. Adeleke, Development of Chicken De-Feathering Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- O. J. Oyebode, O. J. Iyanda, R. S. Adeola, S. Apeh, O. T. Aforolagba-Balogun, O. A. Bayode, S. O. Oladeji, B. C. Finbarrs-Ezema, F. A. Oyebode, S. Egbiki, URBAN WATER MANAGEMENT FOR PUBLIC HEALTH IN NIGERIA: EFFECTIVE GOVERNANCE AND SUSTAINABILITY PERSPECTIVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- B. O. Akinnuli, S. P Ayodeji, S. O. Abadariki, J. O. Fasan, Design, Fabrication and Performance Evaluation of a Reciprocating Cocoa Pod Breaking Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Ayanshola, A.M., , Adidu, J.A, Iji, J.O., , Oladimeji, S.B, Sule, B.F, Salami, A.W. , Bilewu, S.O., ESTIMATING THE POTENTIAL FOR RAINWATER HARVESTING IN ILORIN, NORTH CENTRAL, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.