Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application
- Authors
-
-
A. S. Taiwo
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. O. Daramola
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array, Array
- Abstract
-
This work investigates the effects of particulate palm kernel shell (PKS) on epoxy matrix for the development of composites that can be used as substitute to the conventional metallic bumpers in automobiles. The PKS was sourced from an oil plantation and washed thoroughly with water before sun dried. The dried PKS was pulverized using a laboratory ball mill and sieved into 45 µm particle sizes. Elemental composition of the PKS was determined using XRF. The PKS particulate was randomly dispersed in the epoxy resin to develop composite samples of varied weight contents. The developed samples were tested to determine their impact toughness, wear resistance, flexural, tensile and water absorption properties. The results showed that higher weight contents within 10 - 20 wt.% PKS reinforcement gave the best performance in most of the mechanical properties examined with the exception of tensile and flexural properties which were enhanced at 8 wt.%. Water absorption was noticed to increase as the PKS content increases from 2 - 20 wt.%.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A Amoko, S JUSTINAH, A Fehintola, O Ezekiel, I Oke, A Isaiah, EVALUATION OF EFFECTS OF SELECTED FACTORS ON ADSORPTION KINETICS OF LEAD ION REMOVAL FROM AQUEOUS SOLUTIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Tasiu Ashiru Sulaiman, Ibrahim Aliyu, Yusuf Yau, Ibrahim Bello, ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Michael Emoekpere, Olayide R. Adetunji, Femi T. Owoeye, Koya, Abisoye, K., Adewale, T. Samuel, IN VITRO STUDY OF DIFFERENT SAMPLES OF 316 STAINLESS STEEL AS ORTHOPAEDIC BIOCOMPATIBLE MATERIALS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- T. E. Abioye, DEVELOPMENT OF A POULTRY DE-FEATHERING MACHINE WITH AN ADJUSTABLE BASIN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Adebayo Felix Owa, Abdulahi Olawale Adebayo, Olawale Olarewaju Ajibola, Oluwole Daniel Adigun, Sunday Gbenga Aborisade, Fisayo Adesina, Corrosion Behaviour of Low Carbon Steel in Sulphide Medium Using Thevetia Peruviana as Inhibitor , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, Analyses of Biogas and Digestate from Cattle Dung Anaerobic Digestion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Alfred, V. A, Saliu, M. A, Omoegun, S.O. , Odeyemi, O. Y. , ASSESSMENT OF OXIDE PROPERTIES OF CLAY DEPOSITS FROM ANAMBRA GEOLOGICAL BASIN FOR THEIR SUITABILITY AS CERAMIC RAW MATERIALS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- Dung, M. D.,, Anowai, S.I, Peter, J.A, Dapiya, S.H, Okechalu, J.N, Mawak, J.D, ASSESSMENT OF THE COMPRESSIVE AND SPLITTING TENSILE STRENGTHS OF BIOCONCRETE FROM UREOLYTIC BACTERIA. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.