Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites
- Authors
-
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. Oyetunji
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
AZ61 magnesium alloy composites reinforced with 2 vol.% of carbon nanotubes (CNTs) were synthesized via the powder metallurgy and microwave (MW) sintering techniques. Using a mechanical alloying (MA) process, the CNTs were incorporated into the AZ61 matrix as the reinforcement phase within 15 hours. The milling medium consisted of steel balls with two different diameters to reduce the size of the AZ61 powder and homogeneously distribute the CNTs in the matrix. The CNTs were not damaged during the MA process as confirmed from the Raman spectra of the composite powder. MW sintering was completed in 10 minutes and the sintered samples had a porosity of ~6%. Further characterization showed that the monolithic sample exhibited 42 Hv, 110 MPa, and 136 MPa for microhardness, compressive yield strength and ultimate compressive strength, respectively. Significant improvements were observed in the properties of the composite sample, which amounted to increments of 68% in microhardness, and ~ 21% and ~56% in yield strength and ultimate compressive strength, respectively. The presence of CNTs in the matrix did not compromise the failure strain of the matrix.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- B. O. Akinnuli, S. P Ayodeji, S. O. Abadariki, J. O. Fasan, Design, Fabrication and Performance Evaluation of a Reciprocating Cocoa Pod Breaking Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Samuel Olugbenga Oladele, MODELLING OF THIN-LAYER MICROWAVE DRYING OF BITTER LEAF SAMPLES (Vernonia Amygdalina) FOR PRESERVATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Olabinjo, O. O., , Olusola, G. T. , Sama, M. O., EVALUATION OF PHYSICAL, CHEMICAL AND MICROBIAL PROPERTIES OF DATE FRUIT SEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- O P FAPETU, A O AKINOLA, L L LAJIDE, A B OSASONA, PHYSICOCHEMICAL CHARACTERISTICS STUDY OF OIL EXTRACTED FROM RAFFIA PALM SEED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- I. A. Oke, A. O. Obijole, E. A. Adekunbi, J. O. Babajide, M. D. Idi, T. A. Aladesanmi, THERMAL PROPERTY OF CARBON RESIN ELECTRODES DEVELOPED FOR ELECTROCHEMICAL TREATMENT OF WATER AND WASTEWATERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Oladele, Samouel O. , MICROWAVE THIN-LAYER DRYING KINETICS, DIFFUSIVITY, AND ENERGY EFFICIENCY OF MEDICINAL OCIMUM GRATISSIMUM AND VERNONIA AMYGDALINA LEAVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. C. Chukwuma, Promax2100: A Computer Programme for Design and Optimization of Mineral Processing Plant , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- A. I. Alao, B. K. Adeoye, S. O. Kalu, MICROWAVE-ASSISTED EXTRACTION AND HERBICIDAL POTENTIAL OF CINNAMIC ACID FROM CINNAMON USING RESPONSE SURFACE METHODOLOGY (RSM) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- Samuel L Akingbonmire, L Samuel, O Oluwafemi Omotayo, J O Afolayan, A Banjo Olorunshola, THE PHYSICO-CHEMICAL PROPERTIES OF SOME FINE AGGREGATES IN LOKOJA, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.