Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites
- Authors
-
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. Oyetunji
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
AZ61 magnesium alloy composites reinforced with 2 vol.% of carbon nanotubes (CNTs) were synthesized via the powder metallurgy and microwave (MW) sintering techniques. Using a mechanical alloying (MA) process, the CNTs were incorporated into the AZ61 matrix as the reinforcement phase within 15 hours. The milling medium consisted of steel balls with two different diameters to reduce the size of the AZ61 powder and homogeneously distribute the CNTs in the matrix. The CNTs were not damaged during the MA process as confirmed from the Raman spectra of the composite powder. MW sintering was completed in 10 minutes and the sintered samples had a porosity of ~6%. Further characterization showed that the monolithic sample exhibited 42 Hv, 110 MPa, and 136 MPa for microhardness, compressive yield strength and ultimate compressive strength, respectively. Significant improvements were observed in the properties of the composite sample, which amounted to increments of 68% in microhardness, and ~ 21% and ~56% in yield strength and ultimate compressive strength, respectively. The presence of CNTs in the matrix did not compromise the failure strain of the matrix.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O. A. Adetola, O. J. Olukunle, T. L. Aremu, Investigation of The Effects of Yield On Selected Physical Properties of Cassava Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- B. V. Omidiji, H. A. Owolabi, T. A. Morakinyo, A. Olukoga, Effects of Machining Parameters on the Surface Roughness of Al-Si alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- W. A. Raheem, A. O. Ajayeoba, K. A. Adebiyi, O. R. Oyetunji, O. A. Ayeyemi, Ergonomic Evaluation of Base Transceiver Station Maintenance Personnel in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Ashiru Mohammed, Ibrahim Aliyu, Hussaini Abdullahi Umar, Aliyu Umar Mani, PERFORMANCE EVALUATION OF RAILWAY BALLAST DEGRADATION USING THE MORPHOLOGICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Ifelola Eyitayo Oluwaseyi , EVALUATION OF THE EFFICACY OF ACTIVATED CARBON TREATMENT OF OLAIJA COAL MINE SURROUNDING WATER BODIES, BENUE STATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. E. Abiodun, Determining The Metal Contents of Leach Liqour from Ihietutu Lead and Zinc Ore, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ijagbemi, C.O. , Olabanji, O. M, Abdulmumuni, B, Ashiru, A.R, IJagbemi F.M, PRODUCTION OF ETHANOL GEL FROM CASSAVA AND BANANA PEELS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- J. Isa, M. A. Aderotoye, Effect of moisture content on the physical and aerodynamics properties of cashew nut , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- AWOPETU, O. O, OWOYEMI, J. M, BABATUNDE, T. P. , OJO, O. T., DEVELOPMENT OF A TRANSFORMABLE FURNITURE SYSTEM: FROM SHELVING UNIT TO FUNCTIONAL TABLETOP , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.