Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites
- Authors
-
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. Oyetunji
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
AZ61 magnesium alloy composites reinforced with 2 vol.% of carbon nanotubes (CNTs) were synthesized via the powder metallurgy and microwave (MW) sintering techniques. Using a mechanical alloying (MA) process, the CNTs were incorporated into the AZ61 matrix as the reinforcement phase within 15 hours. The milling medium consisted of steel balls with two different diameters to reduce the size of the AZ61 powder and homogeneously distribute the CNTs in the matrix. The CNTs were not damaged during the MA process as confirmed from the Raman spectra of the composite powder. MW sintering was completed in 10 minutes and the sintered samples had a porosity of ~6%. Further characterization showed that the monolithic sample exhibited 42 Hv, 110 MPa, and 136 MPa for microhardness, compressive yield strength and ultimate compressive strength, respectively. Significant improvements were observed in the properties of the composite sample, which amounted to increments of 68% in microhardness, and ~ 21% and ~56% in yield strength and ultimate compressive strength, respectively. The presence of CNTs in the matrix did not compromise the failure strain of the matrix.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Aderinola, O.S, Ata, G.O, ENHANCING ASPHALT PAVEMENT PERFORMANCE THROUGH PALM KERNEL SHELLS (PKS) INTEGRATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Oyeleye M. O. , Aminu A. k, EVALUATION OF LIGHTNING PROTECTION OF A SOUTH WEST NIGERIA UNIVERSITY LIBRARY EDIFICE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Catherine Mayowa Ikumapayi, Samuel Lambe Akingbonmire, EFFECTS OF BAMBOO LEAF AND LOCUST BEANS POD ASHES ON AUTOGENOUS SHRINKAGE STRAIN AND COMPRESSIVE STRENGTH OF MORTAR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- FADUGBA O.G., EVALUATION OF STRENGTH AND LEACHING PROPERTIES OF SNAIL SHELL ASH (SSA) REMEDIATED PETROLEUM HYDROCARBON CONTAMINATED LATERITIC SOILS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- C. N. Udekwe, A. A. Ponnle, A. O. Omolade, EXPERIMENTAL STUDY ON THE SYNERGISTIC EFFECTS OF COOLING METHODS AND HEAT SINK DESIGN ON THERMOELECTRIC GENERATOR PERFORMANCE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Oluyemi-Ayibiowu B. D, Bello, O, Falola, K. E, A Feasibility Study of Using Electronic Waste as Bitumen Modifier for Sustainable Road Construction and Maintenance , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Akinola, A. O, Yaya-Bankole H. J , EMPIRICAL DETERMINATION OF AIR CONDITIOING INSTALLATION AND MAINTENANCE CHALLENGES IN LAGOS STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- R. K. Apalowo, J. A. Kehinde, E. O. Oyeleke, O. J. Owoloja, S. O. Famuyiwa, MACHINE LEARNING OPTIMIZATION OF UNDERFILL FLOW TIME IN FLIP-CHIP ENCAPSULATION OF BGA ASSEMBLIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.