Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites
- Authors
-
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. Oyetunji
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
AZ61 magnesium alloy composites reinforced with 2 vol.% of carbon nanotubes (CNTs) were synthesized via the powder metallurgy and microwave (MW) sintering techniques. Using a mechanical alloying (MA) process, the CNTs were incorporated into the AZ61 matrix as the reinforcement phase within 15 hours. The milling medium consisted of steel balls with two different diameters to reduce the size of the AZ61 powder and homogeneously distribute the CNTs in the matrix. The CNTs were not damaged during the MA process as confirmed from the Raman spectra of the composite powder. MW sintering was completed in 10 minutes and the sintered samples had a porosity of ~6%. Further characterization showed that the monolithic sample exhibited 42 Hv, 110 MPa, and 136 MPa for microhardness, compressive yield strength and ultimate compressive strength, respectively. Significant improvements were observed in the properties of the composite sample, which amounted to increments of 68% in microhardness, and ~ 21% and ~56% in yield strength and ultimate compressive strength, respectively. The presence of CNTs in the matrix did not compromise the failure strain of the matrix.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M O Idris, EVALUATION OF EFFECTS OF EXTERNAL FACTORS ON DUE DATES PREDICTION IN MANUFACTURING JOBSHOPS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- J. O. Amigun, Seismic Inverted Acoustic Impedance for Lithofacies Discrimination and Reservoir Fluids Prediction: A Case of ‘Ovi’ Field, Niger Delta , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- T E Abioye, DEVELOPMENT OF A POULTRY DE-FEATHERING MACHINE WITH AN ADJUSTABLE BASIN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Adeyanju, Olusiji Ayoade , Adeosun, Tunde Adamson, PRODUCTION ANALYSIS OF FIVE-SPOT MISCIBLE DISPLACEMENT SCHEMES IN GAS CONDENSATE RESERVOIRS. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- C. M. Ikumapayi, COMPARATIVE ANALYSIS OF POLYMER CONCRETE FORMULATED FROM LOW-DENSITY POLYETHYLENE POLYMERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- N S Lawal, A A Babalola, O O Adama, A O Sosanya, A A Adebayo, CHARACTERIZATION OF DIFFERENT CASSAVA EFFLUENTS AND EVALUATION OF PROCESSOR ON-SITE HANDLING TECHNIQUES IN OGUN STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- A. S. Abubakar, Y. A. Sha'aban, Multiple Model Predictive Control for DFIG Based Wind Energy Conversion System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Cyclical Chips Formation during Machining of Titanium and Titanium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.