NEWTON RAPHSON SOLUTIONS OF BIOCHEMICAL OXYGEN DEMAND (BOD) KINETICS
- Authors
-
-
J. O. BABAJIDE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. FEHINTOLA
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
T. A. ALADESANMI
Information Technology and Communications Unit, Obafemi Awolowo University, Ile- Ife, Nigeria
-
M. D. IDI
Land, Air and Water Consulting, F6 Ibrahim Taiwo Estate, Baga Road, Maiduguri, Borno State, Nigeria
-
E. A. ADEKUNBI
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
I. A. OKE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. OBIJOLE
Department of Chemistry, Adeyemi College of Education, Ondo
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
As follow up on our previous studies, this paper evaluated Newton-Raphson method (NRM) solutions of Biochemical Oxygen Demand (BOD) kinetics with the aim of ascertain error free solutions. Non-linear regression, logarithms difference, NRM, least square, daily difference, Thomas, two points, ratio and Fujimoto methods were used to determine constants in BOD kinetics. Microsoft Excel Solver was applied to all the methods. Accuracies of all the methods were evaluated using relative error, Coefficient of Determination (CD), reliability and Model of Selection Criterion (MSC). The study revealed that the values of ultimate BOD and BOD removal rate were in the range of 859 to 1911 mg/l and - 0.140/d to - 0.449 /d respectively. Average total error for the methods were 23.85, 25.7, 74.72, 88.68, 1066.5, 1016.33, 149.12, 78.1 and (61.45 and 59.10) for non-liner regression, logarithms difference, least squares, Thomas, Fujimoto, Ratio, two points, daily difference and NRM ( matrix and graphical).
Accuracy, validity and good fitness of these methods were in order of non-linear regression (8.16) > Logarithm difference (7.72) > NRM (6.26) > least square (6.03) >daily difference (5.42)> Thomas (5.04)> two points (4.14) > ratio (0.63) and Fujimoto (0.51) on basis of their average MSC values. It was concluded that NRM could be used for BOD kinetics. NRM is among the best options because of their simplicity and flexibility as graphical and numerical solutions.
- References
- Downloads
- Published
- 2020-04-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Malomo, B.O., CRASHWORTHINESS AND ENERGY ABSORPTION ANALYSIS OF MESOCARP COIR-FIBRE/EPOXY RESIN-REINFORCED GLASS FIBER HYBRID COMPOSITE LAMINATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- Adekoya A. A, Adelabu, O. S. , Kolawole, F. O., DESIGN OF A DUAL DELTA FUSED DEPOSITION MODELLING 3D PRINTER FOR STUDIO CERAMICS PRODUCTION IN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Michael, O.S, Expired drugs , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- C. M. Ikumapayi, COMPARATIVE ANALYSIS OF POLYMER CONCRETE FORMULATED FROM LOW-DENSITY POLYETHYLENE POLYMERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- C. C. Chiabuotu, T. E. Abioye, O. M. Olabanji, ENHANCING DEPOSITION QUALITY OF ALUMINUM ALLOY 5356 THROUGH OPTIMIZATION OF WAAM PROCESS PARAMETERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- AWOPETU, O. O, OWOYEMI, J. M, BABATUNDE, T. P. , OJO, O. T., DEVELOPMENT OF A TRANSFORMABLE FURNITURE SYSTEM: FROM SHELVING UNIT TO FUNCTIONAL TABLETOP , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Babalola, H. I, FACTOR ANALYSIS OF RECRUITMENT AND SELECTION ATTRIBUTES TO PROMOTE WORKFORCE PERFORMANCE IN THE NIGERIAN CONSTRUCTION INDUSTRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- Uwadia, O.A., Dahunsi, F.M., SOIL NUTRIENT PREDICTION AND CROP PREDICTION RECOMMENDATION SYSTEMS USING IOT AND AI TECHNIQUES: CURRENT TRENDS AND CHALLENGES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
You may also start an advanced similarity search for this article.