NEWTON RAPHSON SOLUTIONS OF BIOCHEMICAL OXYGEN DEMAND (BOD) KINETICS
- Authors
-
-
J. O. BABAJIDE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. FEHINTOLA
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
T. A. ALADESANMI
Information Technology and Communications Unit, Obafemi Awolowo University, Ile- Ife, Nigeria
-
M. D. IDI
Land, Air and Water Consulting, F6 Ibrahim Taiwo Estate, Baga Road, Maiduguri, Borno State, Nigeria
-
E. A. ADEKUNBI
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
I. A. OKE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. OBIJOLE
Department of Chemistry, Adeyemi College of Education, Ondo
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
As follow up on our previous studies, this paper evaluated Newton-Raphson method (NRM) solutions of Biochemical Oxygen Demand (BOD) kinetics with the aim of ascertain error free solutions. Non-linear regression, logarithms difference, NRM, least square, daily difference, Thomas, two points, ratio and Fujimoto methods were used to determine constants in BOD kinetics. Microsoft Excel Solver was applied to all the methods. Accuracies of all the methods were evaluated using relative error, Coefficient of Determination (CD), reliability and Model of Selection Criterion (MSC). The study revealed that the values of ultimate BOD and BOD removal rate were in the range of 859 to 1911 mg/l and - 0.140/d to - 0.449 /d respectively. Average total error for the methods were 23.85, 25.7, 74.72, 88.68, 1066.5, 1016.33, 149.12, 78.1 and (61.45 and 59.10) for non-liner regression, logarithms difference, least squares, Thomas, Fujimoto, Ratio, two points, daily difference and NRM ( matrix and graphical).
Accuracy, validity and good fitness of these methods were in order of non-linear regression (8.16) > Logarithm difference (7.72) > NRM (6.26) > least square (6.03) >daily difference (5.42)> Thomas (5.04)> two points (4.14) > ratio (0.63) and Fujimoto (0.51) on basis of their average MSC values. It was concluded that NRM could be used for BOD kinetics. NRM is among the best options because of their simplicity and flexibility as graphical and numerical solutions.
- References
- Downloads
- Published
- 2020-04-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Tooki, O. O., , Abolade, R. O, Aborisade, D. O., MAPPING OF PLESIOCHRONOUS DIGITAL HIERARCHY SIGNALS INTO SYNCHRONOUS TRANSPORT MODULE FRAME FOR SYNCHRONOUS DIGITAL HIERARCHY SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- Abayomi Olayiwola Eruola, Akeem Makinde, Gbenga Adegboyega Eruola, Kolawole Ayoola, Lugard Nwamini, EFFECT OF FLOAT-WEIGHTS ON DISCHARGE MEASUREMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- M. K. Adeyeri, Assessment of Maintenance Activities of Some Sawmills in Ekiti and Osun States of Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O.A Olubosede, , K. B Adedeji, , C. S Odeyemi,, T. H Shabangu, , DESIGN AND IMPLEMENTATION OF A PID CONTROL FOR A DC MOTOR-DRIVEN BELT CONVEYOR SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Akeju, S. B, Ojo, O. M, Adewumi, J. R. , BOREHOLE WATER QUALITY WITHIN THE FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- Ogundele, O. J, Adebisi, O. I, Adejumobi, I. A, Amusa, K. A. , Alabi, A. A, POWER QUALITY ENHANCEMENT IN AN ELECTRICAL DISTRIBUTION NETWORK USING SHUNT PASSIVE FILTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- OJO, O. T, AWOPETU, O. O, DANLADI, S. T, FATORISA, O. M, DESIGN AND CONSTRUCTION OF A DUAL OPERATED GAS-FIRED MEAT ROASTING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- O. O. Olubanjo, Assessment of Groundwater Quality For Human Consumption And Agricultural Use In Ilara-Mokin, Ondo State, Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- Ubochi, B. C, Olawumi, A. E., , Shuiabu, A. O. , Akingbade, K. F, A WEARABLE FACIAL RECOGNITION DEVICE FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.