NEWTON RAPHSON SOLUTIONS OF BIOCHEMICAL OXYGEN DEMAND (BOD) KINETICS
- Authors
-
-
J. O. BABAJIDE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. FEHINTOLA
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
T. A. ALADESANMI
Information Technology and Communications Unit, Obafemi Awolowo University, Ile- Ife, Nigeria
-
M. D. IDI
Land, Air and Water Consulting, F6 Ibrahim Taiwo Estate, Baga Road, Maiduguri, Borno State, Nigeria
-
E. A. ADEKUNBI
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
I. A. OKE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. OBIJOLE
Department of Chemistry, Adeyemi College of Education, Ondo
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
As follow up on our previous studies, this paper evaluated Newton-Raphson method (NRM) solutions of Biochemical Oxygen Demand (BOD) kinetics with the aim of ascertain error free solutions. Non-linear regression, logarithms difference, NRM, least square, daily difference, Thomas, two points, ratio and Fujimoto methods were used to determine constants in BOD kinetics. Microsoft Excel Solver was applied to all the methods. Accuracies of all the methods were evaluated using relative error, Coefficient of Determination (CD), reliability and Model of Selection Criterion (MSC). The study revealed that the values of ultimate BOD and BOD removal rate were in the range of 859 to 1911 mg/l and - 0.140/d to - 0.449 /d respectively. Average total error for the methods were 23.85, 25.7, 74.72, 88.68, 1066.5, 1016.33, 149.12, 78.1 and (61.45 and 59.10) for non-liner regression, logarithms difference, least squares, Thomas, Fujimoto, Ratio, two points, daily difference and NRM ( matrix and graphical).
Accuracy, validity and good fitness of these methods were in order of non-linear regression (8.16) > Logarithm difference (7.72) > NRM (6.26) > least square (6.03) >daily difference (5.42)> Thomas (5.04)> two points (4.14) > ratio (0.63) and Fujimoto (0.51) on basis of their average MSC values. It was concluded that NRM could be used for BOD kinetics. NRM is among the best options because of their simplicity and flexibility as graphical and numerical solutions.
- References
- Downloads
- Published
- 2020-04-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- B. V. Omidiji, H. A. Owolabi, T. A. Morakinyo, A. Olukoga, Effects of Machining Parameters on the Surface Roughness of Al-Si alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- O. O. Omotayo, S. L. Akingbomire, C. M. Ikumapayi, Sustainable Application of Materials from Construction and Demolition Waste: A Review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- SOYOYE Babatunde Oluwamayokun, FALAYI Folayan Richard, OGUNJIMI Jumoke Omowumi, OLORUNFEMI Emmanuel Olasunkanmi, DEVELOPMENT AND PERFORMANCE EVALUATION OF A MOTORIZED BATTERY-POWERED SPRAYER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- A. O. Owolabi, P. A. Adesida, COST EVALUATION FOR ASPHALT PRODUCTION IN SELECTED QUARRIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- M. A. Akintunde, K A ADETORO, T. J. Abioye, Development of Refrigeration System for Storage and Preservation of Yam Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, POLLUTION OF VEHICULAR EMISSION ANALYSIS AT FEDERAL UNIVERSITY OF TECHNOLOGY AKURE NORTH GATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Oyeleye M. O. , Aminu A. k, EVALUATION OF LIGHTNING PROTECTION OF A SOUTH WEST NIGERIA UNIVERSITY LIBRARY EDIFICE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- R. K. Apalowo, J. A. Kehinde, E. O. Oyeleke, O. J. Owoloja, S. O. Famuyiwa, MACHINE LEARNING OPTIMIZATION OF UNDERFILL FLOW TIME IN FLIP-CHIP ENCAPSULATION OF BGA ASSEMBLIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.