MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES
- Authors
-
-
O. O. Daramola
3Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
O. S. AKINTAYO
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
Epoxy resin with different weight fractions of submicron garlic particles were used to develop epoxy composites. Mechanical properties (tensile, flexural and impact) of the developed composites were characterized. The microstructure of tensile fractured surfaces was examined by Scanning Electron Microscope (SEM) in order to identify the relevant fracture modes involved. Results showed that the tensile strength, tensile modulus, flexural strength, flexural stiffness and impact strength was enhanced in the composites with the tensile strength, tensile modulus and impact strength experiencing peak values at 8 wt.% garlic loading before decreasing. Flexural strength and stiffness increased in a linear mode while elongation at break was found to reduce slightly in the composites when compared to the neat epoxy resin. Microstructure revealed the brittle nature of the neat epoxy. Individual particles with low degree of aggregation were observed in the composites with lower loading. However, particles agglomeration was observed in the highly filled composite (10 wt% garlic) resulting in the termination of the linear increase experienced in the tensile strength, tensile modulus and impact strength results. Overall, the test results demonstrate the competency of garlic particles to serve as a reliable, cost effective and efficient reinforcement material for the development of epoxy reinforced composites.
- References
- Downloads
- Published
- 2025-12-08
- Section
- Articles
- License
-
Copyright (c) 2021 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- R. F. Falayi, P. A. Adeduntan, EFFECTS OF WOODASH AND SAWDUST ADMIXTURE ON ENGINEERING PROPERTIES OF BURNT LATERITE CLAY BRICKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Isa, I, Ajaka E.O, EFFECTIVENESS OF GRAVITY SEPARATION TECHNIQUES FOR THE BENEFICIATION OF DERU SILVER-GOLD ORE, BAUCHI STATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Cyclical Chips Formation during Machining of Titanium and Titanium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Bayode O, Folowosele, T, Akinpelu, O. M, Braimah, J. I , Morakinyo T, WORKABILITY AND MECHANICAL PERFORMANCE ASSESSMENT OF TIGERNUT FIBRE CONCRETE FOR SUSTAINABLE CONSTRUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- M. A. Musa, A. D. Akinwekomi, S. O. Seidu, PRODUCTION AND BIOMEDICAL POTENTIAL OF SILICA NANOPARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- J.A. Ojumu,, EFFECT OF SYNTHESIZED SILVER NANOPARTICLES FROM ALOE VERA PLANT LEAF EXTRACT ON CORROSION BEHAVIOUR OF API 5L IN 0.5M OF H2SO4 , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
