ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE
- Authors
-
-
Tasiu Ashiru Sulaiman
Ahmadu Bello University, Zaria
-
Ibrahim Aliyu
-
Yusuf Yau
-
Ibrahim Bello
-
- Keywords:
- Array
- Abstract
-
This study is aimed at evaluating the combined effect of groundnut shell ash and sawdust ash (GSA/SDA) as partial replacement of ordinary Portland cement in concrete using 1:2:4 mix ratio. The ashes were obtained by the uncontrolled burning process and ground after cooling, the burnt ash was passed through a 75 microns BS sieve. Cement was replaced with 0%, 5%, 10%, 15%, and 20% of GSA/SDA and a water-cement ratio of 0.6 was used. Concrete cubes of 100mm x 100mm x 100mm were cast and cured in water for 3, 14, 21 and 28 days respectively. The result of workability shows that as the GSA/SDA content increased the workability (slump) decreased, but setting times and soundness of GSA/SDA-cement paste increases as the GSA/SDA content increases. However, the compressive strength of GSD/SDA-concrete increases as the curing age increases, and it also increases as the GSD/SDA content increases up to 10% at 28 days then decreases. Finally, it can be concluded that SDA is suitable material for use as a pozzolan since it satisfied the requirement for such a material by having a combined (SiO2+ Al2O3 + Fe2O3) of more than 70%, which was classified as a class C pozzolana, while GSA is a low reactive pozzolan and the optimum percentage of the GSA/SDA to be used should not be more than 10% replacement.
- References
- Downloads
- Published
- 2020-11-18
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. S. Ogbiye, Lucia O. Agashua, Effects of concrete mixing fluid samples - fermented locust beans and sewage on the strength properties of self-healing concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- Dung, M. D.,, Anowai, S.I, Peter, J.A, Dapiya, S.H, Okechalu, J.N, Mawak, J.D, ASSESSMENT OF THE COMPRESSIVE AND SPLITTING TENSILE STRENGTHS OF BIOCONCRETE FROM UREOLYTIC BACTERIA. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- Wilson U.N, Balarabe I, Eze O.C, Adefila A.A, Odeyemi S.O, ASSESEMENT OF COMPRESSIVE STRENGTH OF CONCRETE PRODUCED WITH FINE AGGREGATE FROM DIFFERENT LOCATIONS IN KADUNA STATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- C. M. Ikumapayi, COMPARATIVE ANALYSIS OF POLYMER CONCRETE FORMULATED FROM LOW-DENSITY POLYETHYLENE POLYMERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, K. A. Ezekiel, E. O. Kenvin, Effect of Coarse Aggregate Type on the Modulus of Elasticity of Concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- S. T. Olowolafe, C. M. Ikumapayi, S. L. Akingbonmire, A. A. Olododo, J. A. Ajayi, INFRA-LIGHTWEIGHT CONCRETE: A COMPREHENSIVE REVIEW OF STRUCTURAL AND THERMAL PERFORMANCE WITH SUSTAINABLE AGGREGATES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- A. D. Akinwekomi, I. O. Oladele, A. Oyetunji, Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- E. O. Aiyewalehinmi, O. S. Aderinola, Strength Properties of Commercially Produced Sandcrete block in Ikeja: Lagos State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.