ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE
- Authors
-
-
Tasiu Ashiru Sulaiman
Ahmadu Bello University, Zaria
-
Ibrahim Aliyu
-
Yusuf Yau
-
Ibrahim Bello
-
- Keywords:
- Array
- Abstract
-
This study is aimed at evaluating the combined effect of groundnut shell ash and sawdust ash (GSA/SDA) as partial replacement of ordinary Portland cement in concrete using 1:2:4 mix ratio. The ashes were obtained by the uncontrolled burning process and ground after cooling, the burnt ash was passed through a 75 microns BS sieve. Cement was replaced with 0%, 5%, 10%, 15%, and 20% of GSA/SDA and a water-cement ratio of 0.6 was used. Concrete cubes of 100mm x 100mm x 100mm were cast and cured in water for 3, 14, 21 and 28 days respectively. The result of workability shows that as the GSA/SDA content increased the workability (slump) decreased, but setting times and soundness of GSA/SDA-cement paste increases as the GSA/SDA content increases. However, the compressive strength of GSD/SDA-concrete increases as the curing age increases, and it also increases as the GSD/SDA content increases up to 10% at 28 days then decreases. Finally, it can be concluded that SDA is suitable material for use as a pozzolan since it satisfied the requirement for such a material by having a combined (SiO2+ Al2O3 + Fe2O3) of more than 70%, which was classified as a class C pozzolana, while GSA is a low reactive pozzolan and the optimum percentage of the GSA/SDA to be used should not be more than 10% replacement.
- References
- Downloads
- Published
- 2020-11-18
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- A. J. Abegunde, B. V. Omidiji, P. O. Ajewole, Characterization of Ado-Ekiti River Sand for foundry applications , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Aderinola, O.S, Ata, G.O, ENHANCING ASPHALT PAVEMENT PERFORMANCE THROUGH PALM KERNEL SHELLS (PKS) INTEGRATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- P. A. Adesida, W. A. Salawudeen, ASSESSMENT OF THE INFLUENCE OF MECHANICAL PROPERTIES AND MINERALOGICAL COMPOSITION ON FRAGMENTATION OF SELECTED GRANITIC ROCKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- O. O. Daramola, I. O. Oladele, O. S. AKINTAYO, MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- A. M. Akintade, O. J. Olukunle, J. Isa, Performance Evaluation of an Electromechanical Groundnut Roasting Machine Akintade A.M, Olukunle O. J. and Isa J. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- J. A. Afelumo, O. A. Ademeso, Investigation of the Integrity of Subsoil as Foundation Support for a new Hostel Building, FUT, Akure, Southwestern Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Bamiji Zacheous Adewole, EXPERIMENTAL STUDY ON BED-TO-TUBE HEAT TRANSFER COEFFICIENTS IN BUBBLING FLUIDIZED BED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.