SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA
- Authors
-
-
J T Fasinmirin
-
D O Rapheal
-
J Lazarus
-
- Keywords:
- Array
- Abstract
-
Development of crop coefficient (Kc) can enhance crop water requirement estimates at specific crop growth stages. However, local Kc data are lacking for maize in Omu-aran. Therefore, this research was aimed at quantifying water use and specific Kc values at different growth stages for maize (Zea mays L.) in Omu-Aran,a sub-humid agro-geological zone of Nigeria. A 60cm diameter and 45cm high drainage lysimeter was designed, constructed from a 2.5 mm thick plastic drum, and installed. CROPWAT 8.0 model was later used to develop the Kc and ETc (crop evapotranspiration) using the local weather data of the study site. Soil physical and chemical properties, moisture content, bulk density, and porosity of the site were determined. Weather parameters such average monthly temperature, wind speed, rainfall and relative humidity etc. were collected from an automatic meteorological station located around the research site. Also, irrigation requirements and scheduling for the crop were determined from the model. The average ETc values were 14.6, 43.75, 60.38, and 38.67.0 mm during the initial, development, mid-season and late-season stages, respectively, and the total ETc was 561.8 mm, while the average Kc values for maize were 0.30, 0.73, 1.29 and 0.91 for the initial, development, mid-season, and late-season stages, respectively. The values obtained are suitable for a successful design and implementation of irrigation programme for maize in the study area and this will eventually mean higher productivity and economic development.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Adeyanju, Olusiji Ayoade , Adeosun, Tunde Adamson, PRODUCTION ANALYSIS OF FIVE-SPOT MISCIBLE DISPLACEMENT SCHEMES IN GAS CONDENSATE RESERVOIRS. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- P. A. Adesida, W. A. Salawudeen, ASSESSMENT OF THE INFLUENCE OF MECHANICAL PROPERTIES AND MINERALOGICAL COMPOSITION ON FRAGMENTATION OF SELECTED GRANITIC ROCKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- Ajaka, E. O, Omotehinse, A. O, Kaunda L, MODELS FOR OPERATIONAL CONTINUITY OF A PRECIOUS METAL MINE UNDER FLUCTUATING COMMODITY MARKET , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, M. S. Obot, A. S. Ogunlowo, Modelling the Dehydration Characteristics of Taro (Colocasia Esculenta) Slices in a Convective Cabinet Dryer , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Olatunji Oladimeji Ojo, Taban Emel, ASSESSMENT OF EFFECTIVE NUGGET SIZE, NUGGET ROTATION AND FAILURE MODE OF FRICTION STIR SPOT WELDS OF AA2219-O ALLOY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Cyclical Chips Formation during Machining of Titanium and Titanium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, POLLUTION OF VEHICULAR EMISSION ANALYSIS AT FEDERAL UNIVERSITY OF TECHNOLOGY AKURE NORTH GATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- O. ADERINLEWO, B. ARIBISALA, A. AFOLAYAN, M. TANIMOLA, COMPARATIVE ANALYSIS OF THE USE OF BAMBOO STEM ASH AND CEMENT FOR LATERITIC SOIL STABILIZATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Akinola, A. O, Yaya-Bankole H. J , EMPIRICAL DETERMINATION OF AIR CONDITIOING INSTALLATION AND MAINTENANCE CHALLENGES IN LAGOS STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- W. Lawal, A. A. Akinlabi, O. A. Agbolde, O. Ogunlade, I. A. Olajide, A. O. Adedokun, C. S. Odeyemi, A. O. Owojori, S. O. Akinwande, T. A. B. Akomolafe, T. F. Ogunlade, U. C. Nnamdi, S. O. Oladiran, O. F. Awe, B. T. Ayeni, K. B. Adedeji, I. A. Makinde, U. Lawal, O. C. Adesoba, AN ENSEMBLE-BASED FRAMEWORK FOR DETECTING FAKE NEWS AND MITIGATING DIGITAL MISINFORMATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
You may also start an advanced similarity search for this article.