SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA
- Authors
-
-
J. T. Fasinmirin
Federal University of Technology, Akure
-
D. O. Rapheal
Federal University of Technology, Akure
-
J. Lazarus
Federal University of Technology, Akure
-
- Keywords:
- Array
- Abstract
-
Development of crop coefficient (Kc) can enhance crop water requirement estimates at specific crop growth stages. However, local Kc data are lacking for maize in Omu-aran. Therefore, this research was aimed at quantifying water use and specific Kc values at different growth stages for maize (Zea mays L.) in Omu-Aran,a sub-humid agro-geological zone of Nigeria. A 60cm diameter and 45cm high drainage lysimeter was designed, constructed from a 2.5 mm thick plastic drum, and installed. CROPWAT 8.0 model was later used to develop the Kc and ETc (crop evapotranspiration) using the local weather data of the study site. Soil physical and chemical properties, moisture content, bulk density, and porosity of the site were determined. Weather parameters such average monthly temperature, wind speed, rainfall and relative humidity etc. were collected from an automatic meteorological station located around the research site. Also, irrigation requirements and scheduling for the crop were determined from the model. The average ETc values were 14.6, 43.75, 60.38, and 38.67.0 mm during the initial, development, mid-season and late-season stages, respectively, and the total ETc was 561.8 mm, while the average Kc values for maize were 0.30, 0.73, 1.29 and 0.91 for the initial, development, mid-season, and late-season stages, respectively. The values obtained are suitable for a successful design and implementation of irrigation programme for maize in the study area and this will eventually mean higher productivity and economic development.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. A. Musa, A. D. Akinwekomi, S. O. Seidu, PRODUCTION AND BIOMEDICAL POTENTIAL OF SILICA NANOPARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Adeyemo, Z.K, Bamikefa, I.A, Akande D.O, Ojo, S.I., , Ojerinde, I. A, OPTIMIZATION OF COST 231-HATA PROPAGATION MODEL FOR SELECTED FREQUENCY MODULATION STATIONS IN OSUN STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- O. A. Olubunmi, O. F. Awe, T. R. Ayeni, O. J. Ogundipe, DEVELOPMENT OF A MICROCONTROLLER-DRIVEN OBSTACLE DETECTION AND NAVIGATION SMART EYEGLASSES FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Jegede, B. M, Ojo, O. T, Akinnuli, B. O., EMPIRICAL MODEL AND SOFTWARE DEVELOPMENT FOR CRUDE OIL CARGO QUANTITY MEASUREMENT AND DISCREPANCIES DETERMINATION IN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- Soyoye, B. O. , Akingba, O. O., OPTIMIZATION OF PERFORMANCE PARAMETERS FOR A MAIZE SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 2 (2022): FUTA Journal of Engineering and Engineering Technology
- H. A. Owolabi, B. V. Omidiji, O. C. Falade, Optimization of Poultry Feeds Production Using Linear Programming Technique , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, O. A. Raimi, Determination of Optimum Parameters for Drilling Stainless Steel using Response Surface Methodology (RSM) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Adewuyi, J. R. Adewumi, Optimization of Coagulation-Flocculation Process for the Treatment of Wastewater Using Inorganic and Three Natural Coagulants , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
You may also start an advanced similarity search for this article.