APPRAISAL OF RELATED RISKS WITH LOCALLY MADE BLOCK MAKING MACHINE: A MULTI-SITE CASE STUDY OF NIGERIA BLOCK MAKING INDUSTRY
- Authors
-
-
O. Hezekiah Adeyemi
Department of Mechanical Engineering, Olabisi Onabanjo University, Nigeria
-
B Julius Olorunfemi,
Departments of Mechanical, Federal University Oye Ekiti, Ekiti State,
-
Olasunkanmi O Akinyemi
Departments of Mechanical, Federal University Oye Ekiti, Ekiti State, Nigeria
-
- Keywords:
- Array
- Abstract
-
Non-movement accidents usually arise from the use of machinery and it accounted for more than 10% of all accidents reported yearly. This study evaluated the common risks related to using locally made Block Making Machine (BMM) in 55 block making factories (BMF) located in the Southwest, Nigeria. The objective was to measure the level of exposures of workers to the machine related hazards. Questionnaire, involving 170 workers, and observation methods were used to obtain the safety conditions attached to operating the machines. The hazards prevention program checked by Safety Professionals (SaPro) included machine guarding, environmental hazards control and the use of Personal Protective Equipment (PPE) among others. Non-parametric Chi-Square tests and the independent sample t-test at p<0.05 were used to analyze the data. More than 87% of the total workers suffered injury on the job. Fingers, legs and low-back injuries were mostly reported by 80%, 68.5% and 63.3% workers respectively. Unguarded machinery (78.6%), awkward postures (75%), manual lifting (67%) and carelessness (60%) were the reported risk factors. The Chi-Square test showed that there was significant relationship between the ratings of the operators and the SaPro, on poor machine guarding, access to machine control and environmental control (Chi Square (272) = 8.741E2a , p = .000). The study asserted a need for a redesign of the locally made block making machine for inclusion of safety elements to enhance safety using the machine.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Arowolo, M.O, Abraham, I.O, Olukoya, O.L, Olujoyinbo, E.D, Ade-Omowaye, J.A, DEVELOPMENT OF A FACE-TRACKING ROBOT FOR SAFE DRIVING APPLICATIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- Ogundele, O. J, Adebisi, O. I, Adejumobi, I. A, Amusa, K. A. , Alabi, A. A, POWER QUALITY ENHANCEMENT IN AN ELECTRICAL DISTRIBUTION NETWORK USING SHUNT PASSIVE FILTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Adewuyi, Gideon Akinyemi, Daso, Akindele Wellington, Oke, Peter Kayode, INVESTIGATION AND CHARACTERIZATION OF ELEMENTAL COMPOSITION OF SOLAR PANEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- Raheem, W. A., , Omiyale, A. D, Odeyinka, O. F. , Folorunso, C, A COMPARATIVE ANALYSIS OF PREDICTIVE MODELS FOR HOUSEHOLD ENERGY CONSUMPTION IN LAGOS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- J. J. Obembe, Investigation into Causes of Project Failure in Akure Metropolis, Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- Adedamola Oluwafemi Ojo , Kayode Hassan Lasisi , Fidelis Odedishemi Ajibade, Temitope Fausat Ajibade, Ndeze C. K , DETERMINATION OF THE PHYSICOCHEMICAL PROPERTIES OF WASTEWATER OBTAINED FROM A SOAP-MAKING INDUSTRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- H. A. Owolabi, B. V. Omidiji, O. C. Falade, Optimization of Poultry Feeds Production Using Linear Programming Technique , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- O. O. Olubanjo, Assessment of Groundwater Quality For Human Consumption And Agricultural Use In Ilara-Mokin, Ondo State, Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- Dung, M. D.,, Anowai, S.I, Peter, J.A, Dapiya, S.H, Okechalu, J.N, Mawak, J.D, ASSESSMENT OF THE COMPRESSIVE AND SPLITTING TENSILE STRENGTHS OF BIOCONCRETE FROM UREOLYTIC BACTERIA. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.