APPRAISAL OF RELATED RISKS WITH LOCALLY MADE BLOCK MAKING MACHINE: A MULTI-SITE CASE STUDY OF NIGERIA BLOCK MAKING INDUSTRY
- Authors
-
-
O. Hezekiah Adeyemi
Department of Mechanical Engineering, Olabisi Onabanjo University, Nigeria
-
B Julius Olorunfemi,
Departments of Mechanical, Federal University Oye Ekiti, Ekiti State,
-
Olasunkanmi O Akinyemi
Departments of Mechanical, Federal University Oye Ekiti, Ekiti State, Nigeria
-
- Keywords:
- Array
- Abstract
-
Non-movement accidents usually arise from the use of machinery and it accounted for more than 10% of all accidents reported yearly. This study evaluated the common risks related to using locally made Block Making Machine (BMM) in 55 block making factories (BMF) located in the Southwest, Nigeria. The objective was to measure the level of exposures of workers to the machine related hazards. Questionnaire, involving 170 workers, and observation methods were used to obtain the safety conditions attached to operating the machines. The hazards prevention program checked by Safety Professionals (SaPro) included machine guarding, environmental hazards control and the use of Personal Protective Equipment (PPE) among others. Non-parametric Chi-Square tests and the independent sample t-test at p<0.05 were used to analyze the data. More than 87% of the total workers suffered injury on the job. Fingers, legs and low-back injuries were mostly reported by 80%, 68.5% and 63.3% workers respectively. Unguarded machinery (78.6%), awkward postures (75%), manual lifting (67%) and carelessness (60%) were the reported risk factors. The Chi-Square test showed that there was significant relationship between the ratings of the operators and the SaPro, on poor machine guarding, access to machine control and environmental control (Chi Square (272) = 8.741E2a , p = .000). The study asserted a need for a redesign of the locally made block making machine for inclusion of safety elements to enhance safety using the machine.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. K. Adeyeri, Assessment of Maintenance Activities of Some Sawmills in Ekiti and Osun States of Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Oyefeso, B, Yusuff, O. A., Fadele, O. K, DEVELOPMENT OF PREDICTIVE MASS AND VOLUME MODELS FOR AFRICAN BUSH MANGO (Irvingia gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- S. O. Abdulraman, B. M. Olaleye, M. A. Saliu, Equipment Maintenance Management Audit of Some Granite Aggregate Quarries in Part of South - West Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Oluwatoyin Olaseinde, O. Ajanaku, O. M. Ojo, S. O. Seidu, COMPARATIVE STUDY OF THE REINFORCED STEEL BARS OBTAINED FROM A FAILED RESIDENTIAL BUILDING AND THE SHELVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- W. Lawal, A. A. Akinlabi, O. A. Agbolde, O. Ogunlade, I. A. Olajide, A. O. Adedokun, C. S. Odeyemi, A. O. Owojori, S. O. Akinwande, T. A. B. Akomolafe, T. F. Ogunlade, U. C. Nnamdi, S. O. Oladiran, O. F. Awe, B. T. Ayeni, K. B. Adedeji, I. A. Makinde, U. Lawal, O. C. Adesoba, AN ENSEMBLE-BASED FRAMEWORK FOR DETECTING FAKE NEWS AND MITIGATING DIGITAL MISINFORMATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Olufemi Adeyemi Adetola, M. J. Odu, THE DEVELOPMENT OF A HAND-PUSH WEEDER FOR CUTTING WEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Dahunsi, F. M., , Olawumi, A. O, Sarumi, O. A, Ponnle, A. A, A REVIEW ON ELECTRICAL ENERGY DATASET: MEASUREMENT, FEATURES, AND APPLICATIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- Adeyanju, Olusiji Ayoade , Adeosun, Tunde Adamson, PRODUCTION ANALYSIS OF FIVE-SPOT MISCIBLE DISPLACEMENT SCHEMES IN GAS CONDENSATE RESERVOIRS. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Ajaka E. Oyedele, Alabi O. Oladunni , Omotehinse O. Adeyinka , Minimizing Losses, Socio-environmental Problems and Operational Difficulties in the Activities of Artisanal and Small-scale Gold Mining in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- O. A. Awodele, Appraisal of Risk Identification and Response Techniques adopted on Building Projects in Rivers State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.