EVALUATION OF EFFECTS OF SELECTED FACTORS ON ADSORPTION KINETICS OF LEAD ION REMOVAL FROM AQUEOUS SOLUTIONS
- Authors
-
-
A Amoko
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria
-
S JUSTINAH
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria;
-
A Fehintola
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria;
-
O Ezekiel
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
I Oke
at Civil and Environmental Engineering Department, Elizade University, Ilara- Mokin, Ondo State, Nigeria.
-
A Isaiah
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
- Keywords:
- Lead, Adsorption Kinetics, Microsoft Excel Solver, Analysis of Variance, Mass of Adsorbents, Significant Factors
- Abstract
-
This paper presents a report on the removal of lead ions (Pb2+) from aqueous solutions through adsorption techniques using powdered corncobs. Corncobs were collected from Obafemi Awolowo University agricultural farm. The corncobs were washed with distilled water to remove impurities. The corncobs were dried at room temperature, pulverized, sieved into different particle sizes using standard sieve sizes and stored. Powdered corncobs (PCCS) were separated based on the size. Its micrograph structure, physical and chemical properties were determined using standard methods. The PCCS was used as an adsorbent to remove Pb2+ from aqueous solutions and raw water through batch processes. Effects of the mass of the adsorbent, the initial concentration of Pb2+, initial pH of the aqueous solution and particle size of PCCS on the adsorption kinetics and its models’ parameters were evaluated.
The study shown that moisture content of the PCCS was 7.29 %, volatile solid at 550oC and 1200oC were 96.88 % and 99.44 % respectively. It was also revealed that mass of adsorbent, pH, particle size of the adsorbent, initial concentration of Pb2+ and adsorption time were significant factors that had effects on adsorption of Pb2+ onto PCCS at 95 % confidence level. It was concluded that lead ion can be removed by PCCS, the mass of the adsorbent had significant effects on adsorption kinetics.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. M. Akintade, O. J. Olukunle, J. Isa, Performance Evaluation of an Electromechanical Groundnut Roasting Machine Akintade A.M, Olukunle O. J. and Isa J. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- F I OTU, E I BELLO, T I OGEDENGBE, L LAJIDE, FOURIER TRANSFORM INFRARED SPECTROSCOPIC ANALYSIS OF RUBBER SEED OIL AND ITS BIODIESEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- J. J. Obembe, Investigation into Causes of Project Failure in Akure Metropolis, Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- M. K. Adeyeri, Assessment of Maintenance Activities of Some Sawmills in Ekiti and Osun States of Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- A. R. Iyanda, O. A. Odejobi, Computational Modelling Technique for Short-Term Electric Load Forecasting , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Cyclical Chips Formation during Machining of Titanium and Titanium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- J. Isa, M. A. Aderotoye, Effect of moisture content on the physical and aerodynamics properties of cashew nut , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- J. A.V. Famurewa, E. T. Faboya, The Effects of Drying Temperature on the Physicochemical Properties of Ogbono (lrvingia Gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. O. Olubanjo, A. E. Alade, Development of a Low Cost Greenhouse and Drip Hydroponic Structure for Vegetable Production in South-West Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
You may also start an advanced similarity search for this article.