IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM
- Authors
-
-
S.A. ALABI
Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
The current design approach of railway sleeper is majorly based on some simplifications considered in the European guidelines. One example of these simplifications is how the distribution of the ballast under the sleeper is accounted for. When ballast is damaged, the stiffness it provided to support the sleeper is reduced and the dynamic behavior of the sleeper changes. However, these guidelines consider a uniform distribution of ballast stiffness, either along the complete length of the sleeper or limited to the rail seat. The embedding ballast conditions of railway tracks seemingly vary randomly from site to site and the ballast-sleeper interaction is neither uniformly distributed nor fixed. Therefore, there is need to evaluate the health status of the ballast under the existing railway track. A field test was carried out on an existing ballasted track, to obtain the time domain responses under impact excitation. The measured vertical vibrations at different locations on the in-situ sleeper were employed in time-domain Markov chain Monte Carlo (MCMC)-based Bayesian model updating for identification of the railway track system. MCMC was used to ensure that proposed method can be applied even when the problem is unidentifiable. The proposed method identified the distribution of railway ballast stiffness under low-amplitude vibration and the “equivalent†rail stiffness and mass. The model updating results confirmed that the ballast stiffness under the existing sleeper was uniform, which implies that there was no ballast damage under the tested sleeper.
- References
- Downloads
- Published
- 2020-11-24
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- J.A. Ojumu,, EFFECT OF SYNTHESIZED SILVER NANOPARTICLES FROM ALOE VERA PLANT LEAF EXTRACT ON CORROSION BEHAVIOUR OF API 5L IN 0.5M OF H2SO4 , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Adekoya A. A, Adelabu, O. S. , Kolawole, F. O., DESIGN OF A DUAL DELTA FUSED DEPOSITION MODELLING 3D PRINTER FOR STUDIO CERAMICS PRODUCTION IN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- R. F. Falayi, P. A. Adeduntan, EFFECTS OF WOODASH AND SAWDUST ADMIXTURE ON ENGINEERING PROPERTIES OF BURNT LATERITE CLAY BRICKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Okewale, I.A, Fasan, J.O, Abiwo, O.O, DEVELOPMENT OF A FLOATING RING OEDOMETER FOR TESTING GEOMATERIALS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- 1Obiora-Okeke, O. A, Owolabi, S. H , Adewumi, J. R, HYDRAULIC ASSESSMENT FOR SIGHTING A CONCRETE WEIR ON OGBESE RIVER FOR IRRIGATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Cyclical Chips Formation during Machining of Titanium and Titanium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Tasiu Ashiru Sulaiman, Ibrahim Aliyu, Yusuf Yau, Ibrahim Bello, ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Akinola, A. O, Olusola, E. O, Olundegun, S. A1, DEVELOPMENT OF A PULVERIZING MACHINE FOR RAPHIA PALM SEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- C. N. Udekwe, A. A. Ponnle, A. O. Omolade, EXPERIMENTAL STUDY ON THE SYNERGISTIC EFFECTS OF COOLING METHODS AND HEAT SINK DESIGN ON THERMOELECTRIC GENERATOR PERFORMANCE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- H. A. Owolabi, B. V. Omidiji, O. C. Falade, Optimization of Poultry Feeds Production Using Linear Programming Technique , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.