IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM
- Authors
-
-
S.A. ALABI
Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
The current design approach of railway sleeper is majorly based on some simplifications considered in the European guidelines. One example of these simplifications is how the distribution of the ballast under the sleeper is accounted for. When ballast is damaged, the stiffness it provided to support the sleeper is reduced and the dynamic behavior of the sleeper changes. However, these guidelines consider a uniform distribution of ballast stiffness, either along the complete length of the sleeper or limited to the rail seat. The embedding ballast conditions of railway tracks seemingly vary randomly from site to site and the ballast-sleeper interaction is neither uniformly distributed nor fixed. Therefore, there is need to evaluate the health status of the ballast under the existing railway track. A field test was carried out on an existing ballasted track, to obtain the time domain responses under impact excitation. The measured vertical vibrations at different locations on the in-situ sleeper were employed in time-domain Markov chain Monte Carlo (MCMC)-based Bayesian model updating for identification of the railway track system. MCMC was used to ensure that proposed method can be applied even when the problem is unidentifiable. The proposed method identified the distribution of railway ballast stiffness under low-amplitude vibration and the “equivalent†rail stiffness and mass. The model updating results confirmed that the ballast stiffness under the existing sleeper was uniform, which implies that there was no ballast damage under the tested sleeper.
- References
- Downloads
- Published
- 2020-11-24
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- W. O. Apena, G. A. Oladunni, Comparative Analysis of Path Loss Prediction Models for Selected Rural Areas in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Oyebola Olabinjo, STORABILITY POTENTIAL OF CARROT (Daucuscarota L.) UNDER STEM SPONGE PADDED EVAPORATIVE COOLING STRUCTURES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Olaniyi Alake , COMPRESSIVE STRENGTH OF TERMITE MOUND AND LIME BLENDED CEMENT MORTAR SUBJECTED TO ACIDIC ENVIRONMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- Anthony T. Bolarinwa, Gideon C. Nwafor, OPEN PIT OPTIMIZATION AND PRODUCTION SCHEDULING OF OKOBO COAL MINE, CENTRAL NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- J. O. BABAJIDE, E. O. FEHINTOLA, T. A. ALADESANMI, M. D. IDI, E. A. ADEKUNBI, I. A. OKE, E. O. OBIJOLE, NEWTON RAPHSON SOLUTIONS OF BIOCHEMICAL OXYGEN DEMAND (BOD) KINETICS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ubochi, B. C, Olawumi, A. E., , Shuiabu, A. O. , Akingbade, K. F, A WEARABLE FACIAL RECOGNITION DEVICE FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Odeyemi, C. S, Olaniyan, O. M, Sobowale, A. A, DEVELOPMENT OF REAL TIME HOME AUTOMATION SYSTEM WITH SMS ALERT ON NIGERIA GSM NETWORKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- Arowolo, M.O., , Adaralode, C.I., Ogundigba, H.B, DEVELOPMENT AND IMPLEMENTATION OF A COMPUTER VISION-BASED POTHOLE DETECTOR USING INFRARED CAMERA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, O. S. Adekinya, Assessment of Cost Effectiveness of Borehole Drilling in Oyo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- John Macaulay, Brendan Ubochi, IMPLEMENTION OF A DSPACE CONTROL SYSTEM FOR A NON-ISOLATED DC-DC BOOST CONVERTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.