PERFORMANCE EVALUATION OF RUBBER SEED OIL BIODIESEL
- Authors
-
-
E I BELLO
3Department of Mechanical Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
F I OTU
Department of Mechanical Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
T I OGEDENGBE
3Department of Mechanical Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
L LAJIDE
Department of Chemistry, Federal University of Technology, Akure, Ondo State,Nigeria
-
- Keywords:
- Array
- Abstract
-
In this study the engine performance evaluation of synthesized and characterized rubber seed oil biodiesel was carried out at varying engine speeds and different biodiesel blend levels using a four-cylinder, four-stroke Gardner diesel engine rated at 55.93 KW and 435Nm. The engine was operated on pure rubber seed oil biodiesel, biodiesel blends B10, B20, B30 and B40 with baseline diesel fuel as control. Experimental results showed that the brake torque decreased with increasing engine speed and biodiesel blend percentage while the power produced from the biodiesel blends was less than that produced from the diesel fuel. The power produced decreased as the biodiesel blend concentration increases. The maximum power for the biodiesel blended fuels are 55.14kW, 54 31kW, 54.48kW, 53.15kW, 51.17kW and 48.52kW corresponding to B0, B10, B20, B30, B40 and B100 respectively. The break mean effective pressure increased slightly with increasing engine speed and then sharply decreases with increasing engine speed and biodiesel blend concentration. The brake specific fuel consumption and brake thermal efficiency increased with increasing engine speed and increasing biodiesel blend concentration. The results of this investigation can be used for partial replacement of diesel fuel using low concentration of biodiesel (maximum 30%) produced from rubber seed oil thereby reducing the dependence on petroleum- based diesel fuel.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- IDOWU Abimbola Samson , ADEWUYI B.O, FOLORUNSO D.O, AKINWEKOMI A. D., OPTIMUM INFLUENCE OF CHROMIUM AND COMBINE AUSTEMPERING-CRYOGENIC TREATMENTS ON PERFORMANCE OF DUCTILE IRON , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Emem Ayankop Andi , Ja’afaru Yahaya Bawa, Emem A. A, ’afaru Y. B, EFFECT OF DRILLING PARAMETERS ON DRILLING PERFORMANCE FACTORS IN HORIZONTAL WELLS USING SIMULATION APPROACH. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- W. Lawal, A. A. Akinlabi, O. A. Agbolde, O. Ogunlade, I. A. Olajide, A. O. Adedokun, C. S. Odeyemi, A. O. Owojori, S. O. Akinwande, T. A. B. Akomolafe, T. F. Ogunlade, U. C. Nnamdi, S. O. Oladiran, O. F. Awe, B. T. Ayeni, K. B. Adedeji, I. A. Makinde, U. Lawal, O. C. Adesoba, AN ENSEMBLE-BASED FRAMEWORK FOR DETECTING FAKE NEWS AND MITIGATING DIGITAL MISINFORMATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- O.A Olubosede, , K. B Adedeji, , C. S Odeyemi,, T. H Shabangu, , DESIGN AND IMPLEMENTATION OF A PID CONTROL FOR A DC MOTOR-DRIVEN BELT CONVEYOR SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- O O. Daramola, MECHANICAL PROPERTIES AND WEAR BEHAVIOUR OF KAOLINITE CLAY PARTICLES REINFORCED EPOXY MATRIX COMPOSITES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Aderinola, O.S, Ata, G.O, ENHANCING ASPHALT PAVEMENT PERFORMANCE THROUGH PALM KERNEL SHELLS (PKS) INTEGRATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Oyeleye M. O. , Aminu A. k, EVALUATION OF LIGHTNING PROTECTION OF A SOUTH WEST NIGERIA UNIVERSITY LIBRARY EDIFICE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- M O Idris, EVALUATION OF EFFECTS OF EXTERNAL FACTORS ON DUE DATES PREDICTION IN MANUFACTURING JOBSHOPS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.