Investigation into Causes of Project Failure in Akure Metropolis, Ondo State, Nigeria
- Authors
-
-
J. J. Obembe
Department of Project Management Technology, The Federal University of Technology, Akure
-
- Keywords:
- Investigation, Project Failure, Corruption, Nigeria
- Abstract
-
This paper examined the causes of project failure in both private and public sectors in Ondo State, Nigeria. This was with a view to making recommendations for improved project handling in the study area. The surviving public and private projects in Akure are not many due to the economic crunch in the Country. This indicator makes the researcher selected about two hundred projects both public and private as the research population. Seventy copies of questionnaire were administered to project stakeholders like clients, government contractors, builders, private contractors, consultants, civil engineers, architects and project managers that have practiced for a minimum of ten years. Fifty-five copies (78.6%) of questionnaire were returned and analysed. The analysis utilized the Relative Importance Index (R.I.I) method and the results were presented in form of frequency table and percentages. The study recommended that failure to retain experienced workers, inadequate supply of resources required for project execution, estimates for cost and schedule that are erroneous, corruption, political inference and indolence of workers/contractors were among of the major causes of project failure in the study area. The study concluded that the above causes of project handling be addressed to improve projects execution in Akure, Ondo State, Nigeria.
- References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Abdulwahab J. Yusuf, A. A. Olaniyan, A Modified Droop Controller for Micro-Grid Power Quality Improvement Using Artificial Fish Swarm Algorithm (AFSA) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- J. Isa, M. A. Aderotoye, Effect of moisture content on the physical and aerodynamics properties of cashew nut , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- D. J. Afu, E. O. Ifelola, S. G. Ayodele, A. Ekun, A. Itunu, Survey of the Effects of Operational Noise on Quarry Workers in Akoko-Edo Local Government Area of Edo State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- M. K. Adeyeri, Assessment of Maintenance Activities of Some Sawmills in Ekiti and Osun States of Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- M. M. Melodi, T. G. Onipede, Economic Appraisal of Some Selected Quarries Operation in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, O. S. Adekinya, Assessment of Cost Effectiveness of Borehole Drilling in Oyo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- E.O. OLUKANNI, O.J. OYEDEPO, PHYSICO-RHEOLOGICAL CHARACTERIZATION OF POLYMER MODIFIED BITUMEN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- N G Olaiya, P K Farayibi, P K Oke, A REVIEW ON ADDITIVE MANUFACTURING: LASER TECHNOLOGY METHODS, DISTINCTIONS AND APPLICATIONS IN MANUFACTURING ENGINEERING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- N. G. Olaiya, P. K. Oke, P. B. Mogaji, Development of A Multipurpose Mix-Sieving Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Ogbiye, Lucia O. Agashua, Effects of concrete mixing fluid samples - fermented locust beans and sewage on the strength properties of self-healing concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.