NEWTON RAPHSON SOLUTIONS OF BIOCHEMICAL OXYGEN DEMAND (BOD) KINETICS
- Authors
-
-
J. O. BABAJIDE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. FEHINTOLA
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
T. A. ALADESANMI
Information Technology and Communications Unit, Obafemi Awolowo University, Ile- Ife, Nigeria
-
M. D. IDI
Land, Air and Water Consulting, F6 Ibrahim Taiwo Estate, Baga Road, Maiduguri, Borno State, Nigeria
-
E. A. ADEKUNBI
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
I. A. OKE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. OBIJOLE
Department of Chemistry, Adeyemi College of Education, Ondo
-
- Keywords:
- Wastewater, BOD kinetics, Newton- Raphson method, methods of determining BOD rate, total error, CD MSC, statistical reliability
- Abstract
-
As follow up on our previous studies, this paper evaluated Newton-Raphson method (NRM) solutions of Biochemical Oxygen Demand (BOD) kinetics with the aim of ascertain error free solutions. Non-linear regression, logarithms difference, NRM, least square, daily difference, Thomas, two points, ratio and Fujimoto methods were used to determine constants in BOD kinetics. Microsoft Excel Solver was applied to all the methods. Accuracies of all the methods were evaluated using relative error, Coefficient of Determination (CD), reliability and Model of Selection Criterion (MSC). The study revealed that the values of ultimate BOD and BOD removal rate were in the range of 859 to 1911 mg/l and - 0.140/d to - 0.449 /d respectively. Average total error for the methods were 23.85, 25.7, 74.72, 88.68, 1066.5, 1016.33, 149.12, 78.1 and (61.45 and 59.10) for non-liner regression, logarithms difference, least squares, Thomas, Fujimoto, Ratio, two points, daily difference and NRM ( matrix and graphical).
Accuracy, validity and good fitness of these methods were in order of non-linear regression (8.16) > Logarithm difference (7.72) > NRM (6.26) > least square (6.03) >daily difference (5.42)> Thomas (5.04)> two points (4.14) > ratio (0.63) and Fujimoto (0.51) on basis of their average MSC values. It was concluded that NRM could be used for BOD kinetics. NRM is among the best options because of their simplicity and flexibility as graphical and numerical solutions.
- References
- Downloads
- Published
- 2020-04-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Anthony T. Bolarinwa, Gideon C. Nwafor, OPEN PIT OPTIMIZATION AND PRODUCTION SCHEDULING OF OKOBO COAL MINE, CENTRAL NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Ochuko Mary Ojo, J O Babatola, A A Adesina, A O Akinola, Olurinde Lafe, SYNERGISTIC EFFECT OF CO-DIGESTING DIFFERENT MIX RATIOS OF WATER HYACINTH AND COW-DUNG FOR BIOGAS PRODUCTION. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Oluseyi Orisadare, Ayodeji S. Olawore, Michael O. Ibiwoye, Eyitayo A. Ponle, Omolola T. Odeyemi, Opeyemi S. Kegbeyale, MECHANICAL AND MICROSTRUCTURAL PROPERTIES OF BRASS REINFORCED WITH COCONUT SHELL ASH POWDER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Y. O. Olasoji, S. A. Oyetunji, Propagation Path Loss Model for FM Radio Stations In South West, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- T O Awodola, FLEXURAL MOTION UNDER MOVING MASSES OF PRESTRESSED SIMPLY SUPPORTED PLATE RESTING ON BI-PARAMETRIC FOUNDATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- W. A. Raheem, A. O. Ajayeoba, K. A. Adebiyi, O. R. Oyetunji, O. A. Ayeyemi, Ergonomic Evaluation of Base Transceiver Station Maintenance Personnel in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Ashiru Mohammed, Ibrahim Aliyu, Hussaini Abdullahi Umar, Aliyu Umar Mani, PERFORMANCE EVALUATION OF RAILWAY BALLAST DEGRADATION USING THE MORPHOLOGICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Charity Segun Odeyemi, Ayodeji Oladiran Awodugba, IMPROVING THE EFFICIENCY OF TITANIUM DIOXIDE BASED DYE SENSITIZED SOLAR CELL (DSSC) USING SILVER SURFACE COUNTER ELECTRODE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.