Appraisal of Risk Identification and Response Techniques adopted on Building Projects in Rivers State, Nigeria
- Authors
-
-
O. A. Awodele
Department of Quantity Surveying, Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Building projects, risk identification, risk response, Rivers State, Performance
- Abstract
-
The performance of the construction industry in terms of meeting its objectives or goal has been invariably affected by risks, thereby leading to time and cost overruns. This research therefore assessed the risk identification and response techniques adopted on building projects in Rivers State, Nigeria with a view to enhancing projects performance in the study area. In achieving the aim of the study, primary data were collected through administration of questionnaires to 284 key construction stakeholders comprising the clients, consultants and contractors on completed public building projects in Rivers State, Nigeria. Out of the 284 questionnaires that were distributed, 158 were returned and found suitable for the analysis. Percentile was used for analyzing demographics of the respondents while mean item score was used for ranking of identified techniques. Kruskal Wallis H test was used for examining the differences in the sample means of different groups of respondents. The study revealed good level of awareness of the existing risk identification and response techniques. it was revealed from the study that utilization of past experience, brainstorming and study of project documents were the most used risk identification techniques while the risk transfer, risk reduction and risk sharing were the most utilized response techniques in building projects. The study recommended that stakeholders should visit locations, consult experts and make reference to databases, and historical data from similar projects during risk identification in order to complement the existing utilized techniques while diligently responding to construction risks in the order of transfer, reduction and avoidance were recommended consequent upon the effectiveness of these strategies.
- References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Adebayo Felix Owa, Daniel Toyin Oloruntoba, Muideen Adebayo Bodude, Fisayo Adesina, INVESTIGATION OF MILD STEEL PROTECTION WITH GLASS WOOL IN CORROSIVE MEDIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ashiru Mohammed, Ibrahim Aliyu, Hussaini Abdullahi Umar, Aliyu Umar Mani, PERFORMANCE EVALUATION OF RAILWAY BALLAST DEGRADATION USING THE MORPHOLOGICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Charity Segun Odeyemi, Ayodeji Oladiran Awodugba, IMPROVING THE EFFICIENCY OF TITANIUM DIOXIDE BASED DYE SENSITIZED SOLAR CELL (DSSC) USING SILVER SURFACE COUNTER ELECTRODE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- A. D. Akinwekomi, I. O. Oladele, A. Oyetunji, Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, O. A. Raimi, Determination of Optimum Parameters for Drilling Stainless Steel using Response Surface Methodology (RSM) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- A. A. Ponnle, S. K. Ani, Assessment of Exposure to Indoor Power Frequency Magnetic Fields: SEET Building and Engineering Laboratories, FUTA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- M. O. Oyeleye, T. O. Ale, Foundational Steel Reinforcement Earthing Evaluation: Case of Ogomudia Electrical/Electronics Laboratory Building Extension, Federal University Of Technology, Akure , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- T O Awodola, FLEXURAL MOTION UNDER MOVING MASSES OF PRESTRESSED SIMPLY SUPPORTED PLATE RESTING ON BI-PARAMETRIC FOUNDATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- A. S. Ogbiye, Lucia O. Agashua, Effects of concrete mixing fluid samples - fermented locust beans and sewage on the strength properties of self-healing concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.