Multiple Model Predictive Control for DFIG Based Wind Energy Conversion System
- Authors
-
-
A. S. Abubakar
Department of Electrical Engineering, Ahmadu Bello University, Zaria Nigeria
-
Y. A. Sha'aban
Department of Electrical Engineering, Ahmadu Bello University, Zaria Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
This work developed a multiple input multiple output model predictive control scheme based, for a grid connected wind turbine system with a view to extracting the maximum power from a doubly fed induction generator (DFIG) under an unbalanced condition. The work employed a MMPC scheme for controlling the generator torque and pitch angle simultaneously, so as to reduces the mechanical stress, flicker emission, drive train load and effectively exploit the advantage of high penetration of wind farm. The control strategy was formulated for the whole operating region of the wind turbine system both low and high-speed regime. In addition, multiple model predictive control comprising different MPC was designed based on the operating wind speed. A baseline controller using gain scheduled proportional-integral controller was implemented on a GE 1.5 MW Wind turbine system was used to validate the effectiveness of the developed controller. Based on results obtained, a reduction in 11.04% and 22.42% in flicker emission and drive train load was obtained for the MMPC as compared to PI controller of 0.540752 and 0.216369 respectively at low speed regime (6 m/s). Whilst at high speed regime (16 m/s) the MMPC recorded a reduction in flicker emission and drive train load of 65.36% and 65.21% respectively as compared to baseline controller of 0.032236 and 0.032236 respectively. The performance of the MMPC outperforms the standard baseline in tracking the desire set points using realistic wind speed model with a reduction in both flicker emission and drive train load
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. O. Melodi, B. O. Akinloye, Transmission Capacity Enhancement for Nigerian Power Transmission Grid using TCSC and UPFC , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, Analyses of Biogas and Digestate from Cattle Dung Anaerobic Digestion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Mogaji, T.S, Egunbiyi, T.O, DESIGN AND SIMULATION OF TURBOCHARGER-DERIVED MICROTURBINE SYSTEM FOR COMBINED HEAT AND POWER GENERATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- Adewuyi, Gideon Akinyemi, Daso, Akindele Wellington, Oke, Peter Kayode, INVESTIGATION AND CHARACTERIZATION OF ELEMENTAL COMPOSITION OF SOLAR PANEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- K. O. Oladosu, E. O. Olafimihan, K. A. Babatunde, B. Kareem, A. A. Mustapha, Investigation of Staged Air supply on Grate Combustion of Palm Kernel Shell Mixed with Selected additives (Al2O3 and CaO) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Oluwole Timothy Ojo, FINITE ELEMENT ANALYSIS OF REDESIGNED PIPE-WRENCH FOR OILFIELD SERVICING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- O. A. Adetola, O. J. Olukunle, T. L. Aremu, Investigation of The Effects of Yield On Selected Physical Properties of Cassava Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- John Macaulay, Brendan Ubochi, IMPLEMENTION OF A DSPACE CONTROL SYSTEM FOR A NON-ISOLATED DC-DC BOOST CONVERTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.